Broadcom NetXtreme/NetLink BCM5717 Programmer'S Manual Download Page 171 | Manualshive

Page: 171 / 593

background image

Configuration Space

BCM5718 Programmer’s Guide

Broadcom

®

January 29, 2016 • 5718-PG108-R

Page 171

• MAC local memory

Functional Overview

PCI Configuration Space Registers

The Ethernet controller configuration space can be broken into two regions: Header and Device Specific.

Table 47 on page 172

shows the registers implemented to support PCI/PCI-X/PCIe functionality in the Ethernet

controller. Reserved fields in PCI configuration registers will always return zero.

PCI Required Header Region

The bit-7 of the Header Type register (Offset 0x0E) in the PCI Required Header Region is used to identify
whether the device is a single function device or multifunction device.

Figure 33: Header Type Register 0xE

Single function PCI devices may decode access to non-implemented device functions in two ways, per Section
3.2.2.3.4 of the PCI 2.2 specification:

• A single function device may optionally respond to all function numbers as the same.
• May decode the function number field and respond only to function 0.

The Ethernet controller single function chips follow the stated technique #1— BIOS code scanning
multifunctions get a target response from function(s) 1–7, but these functions are essentially shadows of
function 0. Software that programs to function(s) 1–7 is remapped to function 0.

Note:

BIOS programmers should take special care to read bit_7 in PCI Header Type register (Offset

0x0E) before scanning the Ethernet controller PCI configuration space.

Func

DeviceFunctions:

Single Function = 0

Multi-Function = 1

Header Layout

[0]

[6]

[7]

«
...
169
170
171
172
173
...
»

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

Brand: D-Link Pages: 40

Brand: NEJE Pages: 17

Brand: Oceanic Pages: 13

Brand: Fanimation Pages: 2

Brand: M2M Pages: 24

Brand: Harsco Industrial Pages: 57

Brand: Scanreco Pages: 10

Brand: Teledyne Pages: 102

Brand: BQT Pages: 2

Brand: Conel Pages: 52

Brand: Revox Pages: 57

Brand: Wittenstein Pages: 52

Brand: DEUTSCHMANN AUTOMATION Pages: 30

Brand: VALPES Pages: 28

Easy Clicker UR3-SR

Brand: Universal Remote Control Pages: 2

Brand: salmson Pages: 37

Brand: EBARA Pages: 61

Brand: G-Scale Graphics Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands