manualshive.com logo in svg

Broadcom NetXtreme/NetLink BCM5717, Programmer'S Manual

The Broadcom NetXtreme/NetLink BCM5717 Programmer's Manual is a comprehensive guide for users looking to maximize the functionality of their network adapter. This manual provides detailed instructions on installation, configuration, and troubleshooting. Download this manual for free from manualshive.com to get the most out of your BCM5717.

Share
Download
background image

Ethernet MAC (EMAC) Registers

BCM5718 Programmer’s Guide

 

Broadcom

®

 

January 29, 2016 • 5718-PG108-R

Page 310

EMAC Mode Register (offset: 0x400)

Name

Bits

Access

Default 
Value

Description

Reserved

31:30

RO

0

–

Mac loop back mode control

29

RW

1

1: gate off outgoing TX data path when EMAC 

loopback mode is enabled.
0: TX data will show up in normal functional path 

as well as MAC loopback path. 

Enable APE TX path

28

RW

0

This bit must be written a 1 for the EMAC to 

transmit APE packets.

Enable APE RX path

27

RW

0

This bit must be written a 1 for APE subsystem to 

receive packets from the EMAC

Free Running ACPI

26

RW

0

When this bit is set, the ACPI state machine will 

continue running when a match is found. When 

this bit is clear, the ACPI state machine will halt 

when a match is found.

Halt Interesting packet PME

25

RW

0

When this bit is set, the WOL signal will not be 

asserted on an interesting packet match.

Keep Frame in WOL

24

RW

0

–

Enable FHDE

23

RW

0

Enable receive Frame Header DMA engine. 

Must be set for normal operation.

Enable RDE

22

RW

0

Enable RDMA engine.
Must be set for normal operation.

Enable TCE

21

RW

0

Enable Transmit DMA engine.

Reserved

20

RO

0

–

ACPI Power-on Enable

19

RW

0

Enable Wake on LAN filters when in power-down 

mode

Magic Packet Detection 

Enable

18

RW

0

Enable Magic Packet detection

Send Config Command

17

RW

0

Send config commands when in TBI mode

Flush TX statistics

16

RW

0

Write transmit statistics to external memory.
This bit is self-clearing.

Clear TX statistics

15

RW

0

Clear transmit statistics internal RAM.
This bit is self-clearing.

Enable TX Statistics

14

RW

0

Enable transmit statistics external updates

Flush RX Statistics

13

RW

0

Write receive statistics to external memory.
This bit is self-clearing.

Clear RX Statistics

12

RW

0

Clear receive statistics internal RAM.
This bit is self-clearing.

Enable RX Statistics

11

RW

0

Enable receive statistics external updates.

Reserved

10

RO

0

–

Max Defer

9

RW

0

Enable Max Deferral checking statistic.

Enable TX Bursting

8

RW

0

Enable transmit bursting in Gigabit half-duplex 

mode.

Summary of Contents for NetXtreme/NetLink BCM5717


















































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for NetXtreme/NetLink BCM5717

Badger Basket 9924 User Manual preview
9924
Brand: Badger Basket Pages: 3
C-Nav C-NaviGator III Reference Manual preview
C-NaviGator III
Brand: C-Nav Pages: 20
Danfoss VLT AutomationDrive FC 302 Installation Manual preview
VLT AutomationDrive FC 302
Brand: Danfoss Pages: 128
Danfoss VLT DriveMotor FCP 106 Installation Instructions preview
VLT DriveMotor FCP 106
Brand: Danfoss Pages: 4
Faulhaber MC 5004 Technical Manual preview
MC 5004
Brand: Faulhaber Pages: 66
Vacon 100 HVAC User Manual preview
100 HVAC
Brand: Vacon Pages: 50
V2 Easy3 Manual preview
Easy3
Brand: V2 Pages: 116
V2 WES-BASE Manual preview
WES-BASE
Brand: V2 Pages: 8
V2 CITY2+ Instruction Manual preview
CITY2+
Brand: V2 Pages: 25
V2 CITY1-EVO Manual preview
CITY1-EVO
Brand: V2 Pages: 124
A.R.I. K-060VB M1 Installation Operation & Maintenance preview
K-060VB M1
Brand: A.R.I. Pages: 14
Industrial Controls MC-2120 Operating And Maintenance Manual preview
MC-2120
Brand: Industrial Controls Pages: 17
SolarEdge PV530-R72LGML Installation Manual preview
PV530-R72LGML
Brand: SolarEdge Pages: 20
Woodward ProAct III Installation And Operation Manual preview
ProAct III
Brand: Woodward Pages: 32
Sparkfun Electronics Explorer Dongle Manual preview
Explorer Dongle
Brand: Sparkfun Electronics Pages: 16
H3C WX1804H Configuration Manual preview
WX1804H
Brand: H3C Pages: 11
Nanjing Putian Datang Information Electronics Co., Ltd. CL12/2410LI-A User Manual preview
CL12/2410LI-A
Brand: Nanjing Putian Datang Information Electronics Co., Ltd. Pages: 2
DUNIWAY Stockroom Terranova 960 Instruction Manual preview
Terranova 960
Brand: DUNIWAY Stockroom Pages: 30

Brands by name

Popular brands

Load more brands