Bosch VG5 700 Series User Manual Download Page 33

Page: 33 / 82

AutoDome 700 Series IP PTZ Camera

Configuring the AutoDome 700 Series | en

Bosch Security Systems, Inc.

User Manual

F.01U.273.798 | 3.0 | 2012.08

SC Settings

Click the Default button to restore all camera settings to their original defaults.

SC Data

Click the default button to clear all preposition, privacy mask, and other user settings.

Reboot Device

Performs a reboot of the AutoDome. There is a ten (10) second pause before the dome starts

its homing phase. During the homing phase the camera pans left and right and tilts up and

down. It also adjusts the lens focus. The entire homing phase lasts approximately 40 seconds.

Factory defaults

Click

Restore all defaults

to restore the factory defaults for the camera. A confirmation

screen appears. Allow 5 seconds for the camera to optimize the picture after a mode reset.

4.19

Encoder Profile

For the video signal encoding, you can select a code algorithm and you can change the presets

for the profiles.

You can adapt the video data transmission to the operating environment (for example network

structure, bandwidth, data load). To this end, the AutoDome 700 Series simultaneously

generates two data streams (Dual Streaming), which compression settings you can select

individually, for example one setting for transmissions to the Internet and one for LAN

connections.

Pre-programmed profiles are available, each giving priority to different perspectives.

–

High resolution 1

Target bit rate: 2000 kbps

Maximum bit rate: 4000 kbps

Encoding interval: 30.00 ips

–

High resolution 2

Target bit rate: 1500 kbps

Maximum bit rate: 3000 kbps

Encoding interval: 30.00 ips

–

Low bandwidth

Target bit rate: 700 kbps

Maximum bit rate: 1500 kbps

Encoding interval: 30.00 ips

–

DSL

Target bit rate: 400 kbps

Maximum bit rate: 500 kbps

Encoding interval: 30.00 ips

–

ISDN (2B)

Target bit rate: 80 kbps

Maximum bit rate: 100 kbps

Encoding interval: 30.00 ips

CAUTION!

The AutoDome disables the Privacy Mask function if the orientation is set to Inverted.

Summary of Contents for VG5 700 Series



















































































Search results

Summary of Contents for VG5 700 Series

Reviews:

Related manuals for VG5 700 Series

Brands by name

Popular brands

Bosch VG5 700 Series, User Manual

Search results

Summary of Contents for VG5 700 Series

Reviews:

Related manuals for VG5 700 Series

Brands by name

Popular brands