Blue Seal Evolution Series Service Manual Download Page 85

Page: 85 / 94

Appendix B: Gas Type Conversion

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

Griddle

Carry out the following:-



Remove griddle plate section and heat shield.



Remove main burner.



Disconnect piezo igniter from mounting bracket. (For
access purposes).



Disconnect pilot supply tube from pilot burner to
access pilot injector.

With Main Burner removed, ensure aeration gap is adjusted for type of gas
being used as shown in ‘Gas Specifications Tables’ at rear of this section.

Remove pilot and main injectors and replace with correct size injectors as
shown in ‘Gas Specifications Tables’ at rear of this section.

4. Refit

the

following:-



Re-connect pilot supply tube to pilot burner.



Re-connect piezo igniter to mounting bracket.



Refit main burner, gas control heat shield and griddle plate to cooktop.

Re-light main burners and check flame size on ‘Low’ flame position.



Adjust low fire adjustment screw on open burner gas control valves to obtain
desired flame size.

NOTE:

The 'Low Fire Screw' should be sealed with coloured paint on completion of low
fire adjustment.

Main Burner Injector

Pilot Supply

Tube

Pilot Burner

Piezo Igniter

Low Fire Screw

Burner Aeration Adjustment Screw

Aeration Slide

Summary of Contents for Evolution Series































































































Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands

Blue Seal Evolution Series, Service Manual

Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands