Blue Seal Evolution Series Service Manual Download Page 31

Page: 31 / 94

Service Procedures

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

6.3.2 Open Burner Venturi

Remove control panel (refer 6.1.1).

2. Remove

burner

mounting rail (refer 6.3.1).

Disconnect gas connection from rear of Venturi.

Unscrew and remove Main Injector.

Remove Injector Connector from Venturi.

Remove 2 screws and washers securing burner venturi to
the mounting rail.

Remove Venturi and Gasket fitted between the venturi

and the mounting rail.

Re-assemble in reverse order.

Figure 6.3.2a

Securing Screws

Venturi Gasket

Gas Supply

Connection

Injector Connector

Main Injector

Venturi

Figure 6.3.2b

6.3.4 Main Burner Thermocouple

Remove front control panel (refer 6.1.1).

2. Remove

burner

mounting rail (refer 6.3.1).

Undo thermocouple from burner mounting rail.

Undo thermocouple from rear of gas control valve.

Remove thermocouple from burner mounting rail.

Re-assemble in reverse order.

NOTE: When screwing thermocouple back into gas

control, once threaded up tighten up another ¼
turn only. Do not over-tighten.

Thermocouple.

Undo this Nut.

Figure 6.3.4

Undo Thermocouple

Connections here.

6.3.3 Open Burner Main Injector

Remove front control panel (refer 6.1.1).

2. Remove

burner

mounting rail (refer 6.3.1).

From the underside of the burner mounting Rail, remove
Main Injectors and replace with correct size injectors as
shown in ‘Gas Specifications Tables’ at end of this
section.

Re-assemble in reverse order.

Open Burner Injectors

Main Injector

Figure 6.3.3

Summary of Contents for Evolution Series































































































Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands

Blue Seal Evolution Series, Service Manual

Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands