Blue Seal Evolution Series Service Manual Download Page 30

Page: 30 / 94

Service Procedures

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

6.3 Replacement - Open Burners

(from Ser No. 718550).

6.3.1 Open Burner Mounting Rail

Remove pot stand castings (front and rear).

Remove burner caps and burner bodies (front and rear).

Remove control panel (refer 6.1.1 access).

Disconnect gas valves from gas connections.

Figure 6.3.1a

Figure 6.3.1b

Front and Rear

Pot Stands

Burner Cap

Burner Body

Disconnect Gas

Connections

Figure 6.3.1c

Whilst supporting the burner mounting rail, remove two
screws at either end of rail.

Remove the burner mounting rail complete from the
cooktop.

Replace and re-assemble in reverse order.

Two Screws

Figure 6.3.1d

Figure 6.3.1e

Summary of Contents for Evolution Series































































































Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands

Blue Seal Evolution Series, Service Manual

Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands