Blue Seal Evolution Series Service Manual Download Page 33

Page: 33 / 94

Service Procedures

Blue Seal Evolution Series Gas Convection Ranges

Amendment 13

Pilot Tube Removal

Remove control panel (refer 6.1.1).

2. Remove

burner

mounting rail (refer 6.3.1).

Remove Pilot Injector Assembly as shown earlier in this
section.

Unscrew and remove 2 screws securing pilot burner
shield. Remove shield.

Refit 2 pilot burner shield securing screws to prevent
damaging thermocouple when removing.

Unscrew and remove thermocouple securing nut and
withdraw the thermocouple from Burner Mounting Rail.

Remove 2 pilot burner shield screws and withdraw pilot
tube assembly.

Clean or replace as necessary, and re-assemble in
reverse order.

NOTE: When re-fitting pilot tube and thermocouple to

Burner Mounting Rail, loosely fit 2 pilot burner
shield securing screws to prevent damage to the
thermocouple.

Figure 6.3.6d

Remove 2

Screws

Pilot Burner

Shield

Refit 2

Screws

Thermocouple

Securing Nut

Thermocouple

Figure 6.3.6e

6.3.7 Gas Control Magnet (Cooktop Burners

Only)

Remove control panel (refer 6.1.1).

2. Remove

burner

mounting rail (refer 6.3.1).

Undo thermocouple to gas control valve connection at
rear of gas control valve.

Remove nut at rear of gas control valve.

Remove the magnet from gas control valve.

Replace and re-assemble in reverse order.

Figure 6.3.7b

Thermocouple to Gas

Control Valve Connection.

Magnet

Rear Nut

Gas Control Valve

Figure 6.3.7c

Figure 6.3.7a

Remove this Nut

Rear of Gas

Control Valve

Thermocouple

Connection

Summary of Contents for Evolution Series































































































Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands

Blue Seal Evolution Series, Service Manual

Search results

Summary of Contents for Evolution Series

Reviews:

Related manuals for Evolution Series

Brands by name

Popular brands