manualshive.com logo in svg

Black Box LE2101A-BT-R2, Manual

The Black Box LE2101A-BT-R2 is a cutting-edge device that offers exceptional functionality. It comes with an easy-to-understand manual, allowing users to make the most of its features. You can conveniently download this user manual for free from our website, ensuring a seamless setup and operation experience of this remarkable product.

Share
Download
background image

50

TERMINAL SERVERS

4.5 Configuring Terminal Ports

The most common device used with the Terminal Server is the display
terminal. This section describes the serial port and other settings necessary to
configure the Terminal Server for connection of display terminals. Terminals
may be connected to the Terminal Server using one of two methods:

• Directly-Attached Terminal—The terminal is connected with a cross-cable

(or “null-modem cable”) to the serial port of the Terminal Server. The
Terminal Server supports either RS-232 or RS-423 standard automatically
(there is no need to configure for either). Verify that all cables in use are
within the maximum length specified by these standards.

• Modem-Attached Terminal

—

The terminal is connected via modem and

therefore, avoids the distance limitations mentioned above. The modem
may be asynchronous, leased-line, or any dialup modem. The modem
near the server port should be connected with a straight DCE cable to 
the serial port of the Terminal Server.

4.5.1  P

HYSICAL

C

HARACTERISTICS

— D

IRECTLY

-A

TTACHED

T

ERMINALS

The following examples show some common commands one can use when
configuring terminal ports. Although all of the examples refer to port 2, one
can configure more than one port in each command.

Figure 4-11

shows how to define the physical characteristics of the serial

port.

1. Local> DEFINE PORT 2 AUTOBAUD DISABLED SPEED 19200

2. Local> DEFINE PORT 2 CHARACTER 8 PARITY NONE STOP 1

3. Local> DEFINE PORT 2 FLOW CONTROL XON

Figure 4-11. Configuring a Port for a Directly-Attached Terminal.

Summary of Contents for LE2101A-BT-R2













































































































































































































































Reviews:

No comments

Related manuals for LE2101A-BT-R2

Atop MB5202 Series Hardware Installation Manual preview
MB5202 Series
Brand: Atop Pages: 2
IBM 87302RU Planning And Installation Manual preview
87302RU
Brand: IBM Pages: 140
Bang & Olufsen BeoMaster 5 Manual preview
BeoMaster 5
Brand: Bang & Olufsen Pages: 28
Hologic Cenova User Manual preview
Cenova
Brand: Hologic Pages: 30
Sollae Systems CSE-H20 User Manual preview
CSE-H20
Brand: Sollae Systems Pages: 45
IBM 88861TU Installation And User Manual preview
88861TU
Brand: IBM Pages: 82
Quatech WLNG-AN-DP500 Series Reference Manual preview
WLNG-AN-DP500 Series
Brand: Quatech Pages: 120
Belkin F1UP0002 Quick Installation Manual preview
F1UP0002
Brand: Belkin Pages: 2
Axis NPS 550 User Manual preview
NPS 550
Brand: Axis Pages: 85
disguise rx Hardware Manual preview
rx
Brand: disguise Pages: 12
Digi Connectware PortServer TS 8/16 Configuration And Administration Manual preview
Connectware PortServer TS 8/16
Brand: Digi Pages: 106
HP ProLiant DL185 Quickspecs preview
ProLiant DL185
Brand: HP Pages: 38
HP ProLiant DL320 Generation 4 Maintenance And Service Manual preview
ProLiant DL320 Generation 4
Brand: HP Pages: 70
HP ProLiant DL288 GENERATION 6 User Manual preview
ProLiant DL288 GENERATION 6
Brand: HP Pages: 45
HP ProLiant DL360e Gen8 User Manual preview
ProLiant DL360e Gen8
Brand: HP Pages: 116
HP ProLiant DL20 Generation9 Overview preview
ProLiant DL20 Generation9
Brand: HP Pages: 48
HP ProLiant DL165 Quickspecs preview
ProLiant DL165
Brand: HP Pages: 38
HP ProLiant DL2000 Specification preview
ProLiant DL2000
Brand: HP Pages: 46

Brands by name

Popular brands

Load more brands