Billion 810VGTX User Manual Download Page 22

Page: 22 / 130

Billion 810VGTX Router

Page | 21

DHCP Table

Leased: Shows the information of the DHCP assigned IP addresses.

Expired: Shows the information of all expired IP addresses.

Permanent: Shows the fixed host mapping information.

Leased Table

IP Address: Shows the IP address that is assigned to each client.

MAC Address: Shows the MAC address of each client.

Client Host Name: Shows the Host Name (Computer Name) of the client.

Expiry: Shows the current lease time of each client.

Routing Table

Routing Table

Valid: A check mark indicates a successful routing status.

Destination: Shows the IP address of the destination network.

Netmask: Shows the destination Netmask address.

Gateway/Interface: Shows the IP address of the gateway or the existing interface that this route will use.

Cost: The number of hops counted as the cost of the route.

Summary of Contents for 810VGTX



































































































































Search results

Summary of Contents for 810VGTX

Reviews:

Related manuals for 810VGTX

Brands by name

Popular brands

Billion 810VGTX, User Manual

Search results

Summary of Contents for 810VGTX

Reviews:

Related manuals for 810VGTX

Brands by name

Popular brands