Best WI-Q MERCURY Setup And User Manual Download Page 6 | Manualshive

Page: 6 / 50

background image

6 | Wi-Q™ Mercury Setup and User Guide

FCC | IC CERTIFICATION AND UL EVALUATION

UL EVALUATION (CONTINUED)

• This product is not intended for outside wiring as covered

by Article 800 in the National Electrical Code, NFPA 70.

• Category 5e cabling is the minimum performance category

recommended.

• The minimum conductor gauge permitted to connect be-

tween the PSE or power injector and the PD shall be
26 AWG (0.13 mm2) for patch cords, 24 AWG (0.21 mm2)
for horizontal or riser cable.

•  Connected through standard eight-pin RJ-45 connectors.
•  Evaluated for Mode B only.
•  PoE power is to be supplied by an Access Control System

Unit (ALVY), Class 2 power limited, PoE injector (PSE) pro-
viding 44-52VDC and 15W for maximum output.

«
...
4
5
6
7
8
...
»

Summary of Contents for WI-Q MERCURY



















































Reviews:

No comments

Related manuals for WI-Q MERCURY

Leroy-Somer R180

Brand: Nidec Pages: 20

ClubSport Wheel Base V2

Brand: FANATEC Pages: 39

VLT AQUA Drive FC 202

Brand: Danfoss Pages: 124

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 8

Brand: Danfoss Pages: 114

ECL Comfort 300

Brand: Danfoss Pages: 2

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 24

Brand: Danfoss Pages: 8

ECL Comfort 296

Brand: Danfoss Pages: 159

VLT AutomationDrive FC 301

Brand: Danfoss Pages: 78

Brand: Danfoss Pages: 20

ECL Comfort 210

Brand: Danfoss Pages: 12

ECL Comfort 110

Brand: Danfoss Pages: 8

ECL Comfort 100M

Brand: Danfoss Pages: 21

Brand: Danfoss Pages: 16

Brand: Danfoss Pages: 64

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands