manualshive.com logo in svg

Banner SC22-3, Instruction Manual

Share
Download
Banner SC22-3 Instruction Manual Download Page 93

P/N 133487

     

91

Banner Engineering Corp. 

• 

Minneapolis, U .S .A .

www .bannerengineering .com  •  Tel: 763 .544 .3164

SC22-3 Safety Controller

 

Instruction Manual

Appendix A

Complementary (PNP device): This circuit can meet ISO 

13849-1 category 2, 3, or 4 requirements depending on the 

safety rating and the installation of the output device . This circuit 

can detect a short circuit between channels . In the actuated 

condition (e .g ., S1 ON/S2 OFF below) a short across the closed 

contact can cause the response time to increase based on the 

debounce time . In this situation, the response time could be 

longer than specified, based on the (selected) debounce time, 

see Section 3 .2 .2 .

2-Ch, 2 Terminal

PNP

24V

Rope Pull - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Rope Pull  - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Rope Pull  - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Revision History
1-Aug-2007 Protective Stop was removed from this document and is with the Optical Sensor document

ON

ON

OFF

ON

S1  S2

A.9  Enabling Device

An enabling device is a manually operated control that, 

when continuously actuated, will allow a machine cycle to 

be initiated in conjunction with a start control . Standards 

that cover the design and application of enabling devices 

include:

ISO 12100-1/-2 
IEC 60204-1
ANSI/NFPA 79 
ANSI/RIA R15 .06 
ANSI B11 .19 

A.9.1  Enabling Device Guidelines

Depending on the application, the use of the enabling device 

may require supervision and allow only limited machine 

operation when the individual actuating the device is exposed to 

a hazardous situation . When the enabling device is in use, the 

control of machine motion must be prevented from other sources 

that would override the function of the enabling device . Simply 

actuating the enabling device should not create a hazard .

An enabling device allows a hazardous situation when 

continuously actuated in one position only . In any other position, 

the hazard must be eliminated and the start function be inhibited .
Since an individual’s reaction to an emergency situation may be 

either to release or to tighten the grip, many standards require 

the use of three-position devices:

• Position #1:  the OFF function of the switch (actuator is not 

operated) .

• Position #2:  the enabling function (actuator is operated in its 

midpoint) .

• Position #3:  the OFF function of the switch (actuator is 

operated past its midpoint) .

Release of, or compression past, the midpoint-enabled position 

(#2) of the device must initiate an immediate stopping of 

hazardous motion or situations . It is required that the enabling 

device be released and re-actuated before machine motion can 

be reinitiated .
If allowed, for two-position types, the positions are as follows:

• Position #1:  the OFF function of the switch (actuator is not 

operated) .

• Position #2:  the enabling function (actuator is operated) .

The stop function must be either a functional stop Category 0 

or a Category 1 (see ANSI NFPA79 Section 9) . The design and 

installation of the enabling device must consider the ergonomic 

issues (force, posture, etc .) of sustained activation . A visual 

means of indicating that the device is active may be required .
Only trained and qualified individuals are allowed to operate the 

enabling device if it is bypassing other safeguards . Safe work 

procedures must include, but are not limited to, the use of the 

device, the associated hazards, and the task requiring the use of 

the device .  
If more than one individual is to be safeguarded by the use of 

enabling devices, each individual must have their own device .  

Each enabling device must be concurrently operated before 

machine motion can be initiated .
The means to return the machine to production mode must 

be located outside the hazardous area, where it can not be 

reached from within that area and is guarded against unintended 

operation . In addition, the reset switch operator must have full 

view of the entire guarded area and verify that the area is clear 

of individuals during the reset procedure .

Summary of Contents for SC22-3

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands