Banner SC22-3 Instruction Manual Download

Page: 56 / 128

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Configuration — Onboard Interface

Map Outputs — This option is used to select which of the safety

output(s) the input controls . Any combination of 1, 2, or all 3

outputs may be selected,

but at least one must be selected.

All

safety devices, plus reset and ON/OFF non-safety devices must

be mapped to one or more safety outputs . Map mute enable

devices, mute sensors, and bypass sensors to a safety input

device .

• Select Map Outputs in the Input Properties menu, and press

OK .

• To map the input to an output, use the up/down arrows to

select the output, then press OK .

• A filled-in circle on the display indicates the input is mapped

to the corresponding output; an empty circle indicates the

input is not mapped to that output .

• To add or remove the input mapping, select the output and

press OK . When the input is mapped to the safety outputs

as desired, select Save and press OK .

• After the input is mapped to the safety outputs, the display

returns to the Input Properties menu .

Screen below shows device ES01 mapped to all three

safety outputs.

←

→

Safety Input

(Section 5.5.1)

Non-Safety

Input

(Section 5.5.2)

←

→

←

→

itc

E-

tiv

lin

itc

Add Input

(Section 5.5)

Add an Input continued

Select Reset Logic — To select automatic or manual reset

logic, select Reset Logic and press OK .

• Use the left/right arrows to select the desired reset logic

parameter and press OK .

• After setting the Reset Logic parameter, the display returns

to the Input Properties menu .

Save the Input Device Parameters — When all of the device’s

parameters have been set as desired, select < Done > and

press OK to save the parameters .

• The display will indicate the input parameters were saved .

Press OK to continue .

• The display returns to the Edit Inputs menu .

Summary of Contents for SC22-3

































































































































Search results

Summary of Contents for SC22-3

Reviews:

Related manuals for SC22-3

Brands by name

Popular brands

Banner SC22-3, Instruction Manual

Search results

Summary of Contents for SC22-3

Reviews:

Related manuals for SC22-3

Brands by name

Popular brands