manualshive.com logo in svg

Banner SC22-3, Instruction Manual

Share
Download
Banner SC22-3 Instruction Manual Download Page 59

P/N 133487

     

57

Banner Engineering Corp. 

• 

Minneapolis, U .S .A .

www .bannerengineering .com  •  Tel: 763 .544 .3164

Product Name

 

Instruction Manual

Operating Instructions

Input Status: If a safety output is OFF or turning OFF, line 5 of the 

display indicates information about the input that is keeping the output 

OFF .
Line 5 also indicates when a manual reset operation needs to be 

performed .
NOTES:
•  Line 5 changes to indicate each input when the status of more than 

one input must be displayed .

•  Press the Up arrow button to pause the screen on the current input .
•  Press the Down arrow button to change the last line to the next 

input . (Press the Down arrow button repeatedly to quickly cycle 

through the inputs .)

•  If more than one output is OFF, a small arrowhead indicates the 

safety output to which the input messages correspond (see 

Figure 6-3) .

Input Device 

Status Message

Cause and/or Required Action

Stop

The safety input is in a state that causes the safety output to turn OFF .

Test

A start-up test needs to be completed on the safety input . To perform the test, cycle the input (Run-Stop-Run) to turn 
the safety output ON .

Deactivate

A two-hand control input or an enabling device needs to be cycled (Run-Stop-Run) before the safety output will 
turn ON .

Fault

A problem has been detected with an input that controls the output .

Timed Out

The safety output is in enable mode and the enabling device active time limit has expired . Cycle the enabling device to 
turn the output back ON, or turn the enabling device OFF and perform a system reset to exit Enable mode .

Summary of Contents for SC22-3

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands