Banner SC22-3 Instruction Manual Download

Page: 116 / 128

114

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Appendix C

Add E-Stop Input

To add the E-stop input, select Inputs in the following menu and

press OK .

Select Add Input and press OK .

NOTE: The other options in this menu, Delete Input and Edit

Input, are not covered in this tutorial . These selections

allow you to make changes to an existing configuration .

Input devices are categorized as either safety inputs or non-

safety inputs . The E-stop button is categorized as a safety input .

Select Safety Input and press OK .

The next menu is used to select the type of input device to add .

Icons for the input types are used to make the selection easier .

Use the left/right arrow keys to select the type of input to add, in

this case use the E-Stop icon, and press OK .

Configuring Input Device Properties

The following parameters must be configured for each E-stop

input device:

• Name
• Circuit type
• Terminal assignments
• Advanced settings
• Reset logic
• Output mapping

Enter Input Device Name

After selecting to add an E-Stop Input device the next menu

displayed is the Enter Name menu .
Use the left/right arrow keys to select the character to be

changed, up to 10 characters .
Use the up/down arrow keys to change the character (choices

A-Z, 0-9, -, +, or space) .
In this case, the name of the E-Stop Input was set to the default

value of ES01 . Do not change the name of the device at this

time; just press OK .

Input Properties Menu

The next menu displayed is the Input Properties menu .

Set the Circuit Type of the Input

From the Input Properties menu select Select Circuit Type and

press OK .

The display will show the Select Circuit Type menu .
The left/right arrow keys select the circuit type of the input

device . Select the circuit type Dual Ch., 4 terminal and press

OK .

When the circuit type is selected, the display returns to the Input

Properties menu .

Edit the Terminal Assignments

When the input circuit type was selected, the Safety Controller

automatically assigns terminals for the input device . These

terminal assignments can be viewed and changed by selecting

Edit Terminals and pressing OK .

Summary of Contents for SC22-3

































































































































Search results

Summary of Contents for SC22-3

Reviews:

Related manuals for SC22-3

Brands by name

Popular brands

Banner SC22-3, Instruction Manual

Search results

Summary of Contents for SC22-3

Reviews:

Related manuals for SC22-3

Brands by name

Popular brands