manualshive.com logo in svg

Banner SC22-3, Instruction Manual

Share
Download
Banner SC22-3 Instruction Manual Download Page 81

P/N 133487

     

79

Banner Engineering Corp. 

• 

Minneapolis, U .S .A .

www .bannerengineering .com  •  Tel: 763 .544 .3164

SC22-3 Safety Controller

 

Instruction Manual

Appendix A

A.3.2  SC22-3 Interlock Switch Hookup Options 

NOTE:  All figures are shown with the gate (guard) in the closed, 

or Run, state . The safety contact is considered to be 

the normally closed contact that is of a positive-opening 

design (unless otherwise noted), normally marked with 

the 

 symbol .

Single-Channel (1 terminal, 2 terminals, or PNP device): 

These circuits can typically meet ISO 13849-1 Category 2 

requirements, depending on the design and installation of the 

switch . At a minimum, the switch must be a safety-rated device 

to achieve a Category 2 level . The 1-terminal and the PNP 

device can not detect a short circuit to another source of power . 

2-terminal hookup uses pulse monitoring and can detect a short 

circuit to another source of power . Fault Exclusion must be used 

to achieve a higher level of safety circuit integrity .

2-Ch, 2 Terminal

PNP

24V

Rope Pull - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Rope Pull  - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Rope Pull  - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Revision History
1-Aug-2007 Protective Stop was removed from this document and is with the Optical Sensor document

ON

ON

OFF

ON

               

2-Ch, 2 Terminal

PNP

24V

Rope Pull - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Rope Pull  - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Rope Pull  - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Revision History
1-Aug-2007 Protective Stop was removed from this document and is with the Optical Sensor document

ON

ON

OFF

ON

               

2-Ch, 2 Terminal

PNP

24V

Rope Pull - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Rope Pull  - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Rope Pull  - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Revision History
1-Aug-2007 Protective Stop was removed from this document and is with the Optical Sensor document

ON

ON

OFF

ON

Dual-Channel (2 terminals or 3 terminals): This circuit typically 

can meet ISO 13849-1 category 2 or category 3 requirements, 

depending on the design and installation of the switch(es) . Dual-

channel 3-terminal hookup uses pulse monitoring and can detect 

a short circuit to another source of power . Both 2- and 3-terminal 

hookups can detect a short between channels if the contacts are 

open longer than 2 seconds .

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

A single switch 
mounted on a single 
guard is typically a 
Category 2 applicaton .

Two switches 
individually mounted 
on a single guard is 
typically a Category 
3 applicaton .

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

Dual-Channel (PNP device): This circuit can meet ISO 13849-1 

category 2, 3, or 4 requirements depending on the safety rating, 

installation, and the fault detection (e .g ., short circuit) capabilities 

of the device(s) . The SC22-3 does not provide short circuit 

detection in this configuration .

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

Dual-Channel (4 terminals): This circuit can meet ISO 13849-1 

Category 2, 3, or 4 requirements, depending on the design and 

installation of the switch(es) . This circuit can detect a short circuit 

between channels or to another source of power .

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

Two switches 
individually mounted 
on a single guard is 
typically a Category 
4 application . A 
series connection 
of switches on 
multiple guards is 
typically a Category 
3 application .

One switch 
mounted on a 
single guard is 
typically a Category 
2 application .

Complementary (2 terminals or 3 terminals): This circuit can 

meet ISO 13849-1 Category 2, 3, or 4 requirements depending 

on the design and installation of the switch(es) . This circuit can 

detect a short circuit between channels . A coded magnetic switch 

would typically use this style . In the guard closed condition 

(as shown) a short across the closed contact can cause the 

response time to increase based on the debounce time . In this 

situation, the response time could be longer than specified, 

based on the (selected) debounce time, see Section 3 .2 .2 .

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

A single coded magnetic switch mounted 
on a single guard can meet Category 3 or 4 
depending on installation and the frequency 
of exercising the guard (closed-open-closed) . 
For more information, see the GM-FA-10J data 
sheet (p/n 60998) .

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

2-Ch, 2 Terminal

PNP

24V

Gate Switches - Single Channel

1-Ch.

1 Terminal

1-Ch.

2 Terminals

1-Ch.

1 Term, PNP

Gate Switches - Dual Channel

2-Ch, 2 Terminals

2-Ch, 3 Terminals

2-Ch, 4 Terminals

24V

Gate Switches - Dual Channel Complementary

Complementary,

2 Terminals

Complementary,

3 Terminals

Complementary,

2 Terminals, PNP

24V

Gate Switches - 2x Dual Channel Complementary

2x Complementary,

4 Terminals

2x Complementary,

5 Terminals

2x Complementary,

4 Terminals, PNP

24V

Rev C - Corrected  “OFF” and “ON” on Two-hand Operation - 2x Dual Channel Complementary, 2x Complementary, 4 Terminals, 4 PNP
20-Sept-06 Rev. D - Moved 24V, ON and OFF text closer to drawings.
21-Nov-06 Rev. E - Added + sign to 1-Ch, 2 Terminals; 2-Ch, 3 and 4 Terminals; Complementary, 3 Terminals; 2x Complementary, 5 Terminals
08-Dec-06 Rev. F - Changed 2x Complementary, 4 Terminals, PNP from OFF ON - OFF ON to ON OFF - ON OFF
10-Jan-07 Rev. G - C sign text to outlines
25-May-07 Rev. H - Changed Single Channel PNP; 2-Ch, 2 Terminal PNP;  Complementary, 2 Terminal, PNP; 2x Complementary, 5 Terminals and 2x Complementary, 4 Terminals, PNP

ON

ON

OFF

ON

OFF

ON

OFF

ON

Summary of Contents for SC22-3

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands