manualshive.com logo in svg

Banner SC22-3, Instruction Manual

Share
Download
Banner SC22-3 Instruction Manual Download Page 112

 110     

P/N 133487

Banner Engineering Corp. 

• 

Minneapolis, U .S .A .

www .bannerengineering .com  •  Tel: 763 .544 .3164

SC22-3 Safety Controller 

 

Instruction Manual

Appendix B

Edit the Configuration

• If there is a need to edit one of the properties during the 

confirmation process, select Edit .
•  Selecting the Edit button will open up the Properties menu for 

the device . Make the change and then select OK .

   If you change one or more device properties during 

the manual verification stage of the confirmation, the 

Controller will need to re-validate the code. 

•  When you complete the edit and select OK, a message will 

appear asking whether you want to proceed to edit any other 

devices or if you want to restart the confirmation process .

When the configuration is successfully confirmed, the Controller 

will switch to Run mode, as described earlier, and wait for a 

system reset .

B.7 Other Functions

Receive a Configuration from the Controller (see Section 4.5.1)

To receive (upload) a configuration from a Controller and display 

it in the PCI:
•  Connect the SC22-3 Controller to the PC using the USB cable 

(see Section 1 .3 .1 .) .  

• Apply 24V dc power to the Controller .
• Click on the Receive button in the tool bar . 

Send a Configuration to the Controller (see Section 4.5.2)

To send (download) a configuration from the PCI to a Controller:
•  Connect the SC22-3 Controller to the PC using the USB cable 

(see Section 1 .3 .1 .) .

• Apply 24V dc power to the Controller .
•  Click on the Open button in the tool bar and open the intended 

configuration file .

• Click on the Send button in the tool bar . 

 

NOTE:  

Confirming

 a configuration also 

sends

 the configuration 

to the Controller .

Open a Configuration from the XM Card (see Section 4.5.3)

To open a copy of a configuration from the XM card and display it 

in the PCI:

•  Connect the SC-XMP programming tool to the PC using the 

USB cable (see Section 1 .3 .1) .

• Insert the XM card into the programming tool .
• Open the File menu in the upper left of the PCI tool bar .
• Select Open From XM Card .
A message will appear when the operation is complete .
NOTE:  Both confirmed and unconfirmed configurations can be 

sent to or received from the XM card .

Send a Configuration to the XM Card (see Section 4.5.4)

To send a copy of a configuration from the PCI to the XM card:
•  Connect the SC-XMP programming tool to the PC using the 

USB cable (see Section 1 .3 .1) .

• Insert the XM card into the programming tool .
•  Click on the Open button 

 in the PCI tool bar and open 

the intended configuration file .

• Open the File menu in the upper left of the PCI tool bar .
• Select Send To XM Card .
A message will appear when the operation is complete .
NOTE:  Both confirmed and unconfirmed configurations can be 

sent to or received from the XM card .

Lock the XM Card (see Section 4.5.5)

To Lock the XM card so that the stored configuration cannot be 

changed (this operation cannot be undone):
• Insert the XM card into the programming tool .
•  Click on the Open button 

 in the PCI tool bar and open 

the intended configuration file .

• Verify that the correct file is stored on the XM card .
• Open the File menu in the upper left of the PCI tool bar .
• Select Lock XM Card .
A message will appear when the operation is complete . 

Change the Controller Password (see Section 4.5.6)

To change a Controller password from the PCI:

• Connect the Controller to the PC, using the USB cable . 
• Apply 24V dc power to the Controller .
• Open the File menu in the upper left of the PCI tool bar .
• Select Change Safety Controller Password .
• Fill in the menu that will appear as needed .
• Record the new password and click OK .

Summary of Contents for SC22-3

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands