Banner SC22-3 Instruction Manual Download | Manualshive

Page: 44 / 128

background image

42

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Configuration — PC Interface

4.5.6 Changing the Password Using the Personal

Computer Interface (PCI)

For this procedure, the PC must be connected to the Controller

via USB cable, and the Controller must be ON .
1 . Go to File > Change Safety Controller Password . The

Change Password screen will appear .

Figure 4-13. Change Password screen

2 . Fill in the boxes for Safety Controller password, new

password, and new password again . Click OK .

3 . The Entering Configuration Mode screen will appear, saying,

“Are you sure you want to do this? All safety outputs will be

turned off .” (If you click Yes, all safety outputs will turn OFF,

along with the machine or system the Safety Controller is

monitoring .)

4 . Click Yes . The Change Password screen will reappear .
5 . Click Close . The password is now changed . Record the

password for safekeeping .

NOTE: If the password becomes lost, contact Banner

Engineering for assistance .

4.5.7 Export Documents

The configuration documents (wiring diagram, ladder logic

diagram and configuration summary) can be saved as either .pdf

or .dxf files . To export a configuration file:
• Open the configuration file that you want to save .
• Go to File > Export in the upper left of the tool bar .
• Select the configuration document you want to export .
• Verify that the File name is correct and pick the Save as type

file option ( .pdf or .dxf) you need .

• Select Save .

Figure 4-14. Save As screen

4.5.8 Print Options

To print a configuration file:
• Open the configuration file that you want to print .
• Go to File > Print in the upper left of the tool bar .
• Select the configuration document (wiring diagram, ladder logic

diagram, or configuration summary) you want to print .

• A Page Setup menu will appear . Make the page and printer

choices and click OK . (Hint: Wiring diagrams typically fit the

page better when “landscape” is selected; the other documents

fit better on “portrait .”)

«
...
42
43
44
45
46
...
»

Summary of Contents for SC22-3

































































































































Reviews:

No comments

Related manuals for SC22-3

Brand: NEC Pages: 304

Brand: ZKTeco Pages: 8

Brand: EasyIO Pages: 18

Brand: ECKELMANN Pages: 178

Brand: echoflex Pages: 8

Brand: H3C Pages: 17

Brand: H3C Pages: 32

VARIVENT D Series

Brand: GEA Pages: 78

Brand: GEA Pages: 96

Brand: GEA Pages: 66

Brand: UNI Pages: 21

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: HandyTrac Pages: 14

Brand: TA Pages: 6

Brand: K1EL Pages: 46

Brand: K'Nex Education Pages: 56

Brand: Lamtec Pages: 136

Brand: National Instruments Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands