Banner SC22-3 Instruction Manual Download

Page: 73 / 128

P/N 133487

Banner Engineering Corp.

•

Minneapolis, U .S .A .

www .bannerengineering .com • Tel: 763 .544 .3164

SC22-3 Safety Controller

Instruction Manual

Troubleshooting and Maintenance

8.6 Fault Diagnostics — OBI

Troubleshooting the Controller and connected I/O devices is

easy using the Onboard Interface . Any event that causes a

safety output to turn OFF or stay OFF (either for fault or input

stop events) will be immediately detected and displayed on the

Controller’s display . Further information about current and past

faults can be accessed using the Fault Diagnostics menu . To

get to the Fault Diagnostics menu, press OK from the Run mode

menu . Select Fault Diagnostics and press OK .

Figure 8-3. Select Fault Diagnostics — OBI

The Diagnostics menu provides three choices: view fault

conditions that currently exist, view faults that have been stored

in the fault log, and clear the fault log .

8.6.1 View Current Faults

To view current fault conditions, select View Current Faults

using the up/down arrow buttons and press OK .

Figure 8-4. View current faults — OBI

The screen shows the fault conditions that currently exist, one

at a time . Use the left/right arrow keys to view all the faults .

(Shortcut: To view current faults when the Run mode screen is

displayed, simply press OK three times .)

• The top line of the Current Fault menu indicates which device

has the fault .

• The second and third lines provide a brief description of the

fault .

• The fourth line provides a suggestion for correcting the fault .
• The fifth line provides the fault code . Use the fault code and

information in Section 8 .x to obtain more information about

the fault and additional suggestions for correcting it .

Use the left/right arrow (< and >) buttons to access fault

information for all faulty devices .

Figure 8-5. Current Fault screens — OBI

Arrowhead designates location of additional fault screens

Device Name

Fault

Description
Suggested

Remedy
Fault Code

Summary of Contents for SC22-3

































































































































Search results

Summary of Contents for SC22-3

Reviews:

Related manuals for SC22-3

Brands by name

Popular brands

Banner SC22-3, Instruction Manual

Search results

Summary of Contents for SC22-3

Reviews:

Related manuals for SC22-3

Brands by name

Popular brands