Bandit
35
Copyright 3/19
MODEL BTC-150
MAINTENANCE
DAILY START UP & MAINTENANCE cont.
25. Inspect, adjust, and lubricate tracks:
Inspect, adjust, and lubricate tracks as needed per
track MFG. manual.
26. Check around machine:
Check around the entire machine for tools, cans,
saws, etc. All tools not in use should be stored in
a tool box.
27.
Clean off mower/stump grinder attachment
(if equipped):
Clean off the mower or stump grinder attachment
daily. Remove any debris that builds up on top of
either attachment, especially around the hydraulic
hoses. This may need to be done more than once a
day, depending on the application.
28. Review all safety procedures on decals, from
manual, and from video.
29. Make sure all safety equipment is being worn:
Make sure you are wearing all of your safety
equipment: hard hat, face shield, gloves, eye
protection, ear protection, etc.
30. Turn battery disconnect switch on.
31. Make sure the throttle switch is in the idle
position on the control panel.
32. Remember to check EVERYTHING on the
checklist.
WEEKLY MAINTENANCE
1. Grease the mower attachment's overhung
load adapter (if equipped):
Grease both zerks with 1 - 2 pumps every 30 hours,
or once a week with a synthetic NLGI#2 type grease.
2. Lubricate all steel friction areas:
Lubricate all steel friction areas including, but not
limited to pivoting, hinged, sliding, rotating areas
on the machine (i.e. doors, cab tilt hinge, winch
rollers, etc.)
3. Remove the beltshield on mower/stump
grinder attachment and clean out (if equipped):
Remove the beltshield on mower or stump grinder
attachment, wipe off any grease that has built up
around the bearings and remove any debris that
has built up.
4. Check alternator and fan belts on engine (as
applicable):
Adjust and maintain per the engine manufacturer’s
manual.
MONTHLY MAINTENANCE
1. Check hydraulic pressures:
Check, reset and maintain all hydraulic pressure
settings to the specified maximum, see page 51.
This will give you the best performance from the
hydraulic system.
2. Check cab tilt pump reservoir:
Keep full of hydraulic oil, Petro-Canada Hydrex XV.
3 MONTH MAINTENANCE
1.
Hydraulic oil filter (In-Tank):
Must be replaced after FIRST 10 HOURS OF
OPERATION, USE A 10 MICRON FILTER. After first
change replace oil filter every 3 months or 400 hours.
2.
Charge filters (total of 3):
Must be replaced after first 10 hours of operation.
Use a 10 Micron filter. After first change replace
charge filters every 3 months or 400 hours. All charge
filters are located between the cab and hydraulic
and fuel tanks.
6 MONTH MAINTENANCE
1. Windshield Wiper:
Check the windshield wiper. Replace as needed.
1. Hydraulic oil:
Change hydraulic oil and flush the hydraulic reservoir
tanks.
2. Fuel tank:
Drain and clean the fuel tank yearly.
YEARLY MAINTENANCE
3. Hydraulic suction screens:
Change hydraulic suction screens yearly or every
2000 hours.
4. Cab tilt pump reservoir:
Change ATF transmission oil and flush the cab tilt
pump reservoir.
Summary of Contents for BTC-150
