AWB OD200-IDU Operator'S Manual Download Page 87

Page: 87 / 114

MAC Authentication

8-9

Figure 8-6. MAC Authentication

System Default

– Specifies the action for MAC addresses listed in the local MAC

Authentication Table.

•

Deny:

Blocks access for all MAC addresses listed in the MAC Authentication

Table. Clients with MAC addresses not listed in the table are permitted access.

•

Allow:

Permits access for all MAC addresses listed in the MAC Authentication

Table. Clients with MAC addresses not listed in the table are denied access.

Local MAC Filter Settings

– Adds new MAC addresses to the MAC Authentication

Table, or removes addresses currently listed in the table.

•

MAC Address:

Physical address of a client. Enter six pairs of hexadecimal digits

separated by colons; for example, 00:90:D1:12:AB:89.

•

Permission:

Select Add to list a new specified MAC address in the MAC

Authentication Table. Select Delete to remove the specified MAC address from the
table.

•

Update:

Performs the Add or Delete action on the specified MAC address.

MAC Authentication Table

– Displays current entries in the MAC filter database.

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands