AWB OD200-IDU Operator'S Manual Download Page 79 | Manualshive

Page: 79 / 114

background image

8-1

Chapter 8: Wi-Fi Settings

The OD200 model for the 3.5 GHz WiMAX band includes an IEEE 802.11g radio
interface for local Wi-Fi communications. The Wi-Fi set up pages include
configuration options for the radio signal characteristics and Wi-Fi security.

The Wi-Fi configuration pages include the following options.

Wireless Settings

From the Wireless menu, click on Settings to configure the unit’s Wi-Fi radio
interface. The unit’s radio can operate in three modes, IEEE, 802.11b & g, 802.11g
only, and 802.11b only.

The IEEE 802.11g standard operates within the 2.4 GHz band at up to 54 Mbps.
Note that because the IEEE 802.11g standard is an extension of the IEEE 802.11b
standard, it allows clients with 802.11b wireless network cards to associate to an
802.11g access point.

Table 8-1 Wi-Fi Settings

Menu

Description

Page

Settings

Allows you configure basic radio parameters.

Security

Configures Wi-Fi security features.

MAC Authentication

Configures a client MAC address control list.

«
...
77
78
79
80
81
...
»

Summary of Contents for OD200-IDU



















































































































Reviews:

No comments

Related manuals for OD200-IDU

Brand: Juniper Pages: 2

Brand: SerVision Pages: 40

Brand: NETGEAR Pages: 7

Smart Command 410100

Brand: Caroma Pages: 2

NetLink Wireless Telephone

Brand: SpectraLink Pages: 30

Fieldgate PAM SFG600

Brand: Endress+Hauser Pages: 20

Firebox SSL Core

Brand: Watchguard Pages: 20

Brand: Cradlepoint Pages: 148

Brand: NavCom Technology Pages: 7

Brand: SignaMax Pages: 54

Brand: Renu Electronics Pages: 46

Brand: IBM Pages: 28

Brand: Symantec Pages: 100

CT.TS005.002606

Brand: Talkswitch Pages: 29

Brand: Yoda Pages: 3

Brand: IFM Electronic Pages: 44

NetComm CloudMesh NF18MESH

Brand: Casa Systems Pages: 5

Brand: Clipcomm Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands