AWB OD200-IDU Operator'S Manual Download Page 7 | Manualshive

Page: 7 / 114

background image

iii

About This Guide

Purpose

This guide details the hardware features of the WiMAX Residential Gateway including its
physical and performance-related characteristics, and how to install the device and use its
configuration software.

Audience

The guide is intended for use by network administrators who are responsible for operating
and maintaining network equipment; consequently, it assumes a working knowledge of
general networking concepts, the Internet Protocol (IP), and Simple Network
Management Protocol (SNMP).

Conventions

The following conventions are used throughout this guide to show information:

Note:

Emphasizes important information or calls your attention to related features or
instructions.

Caution:

Alerts you to a potential hazard that could cause loss of data, or damage the
system or equipment.

Warning:

Alerts you to a potential hazard that could cause personal injury.

Related Publications

The following publication gives basic information on how to install and use the WiMAX
Residential Gateway.

Quick Installation Guide

As part of the WiMAX Residential Gateway’s software, there is online help that describes
all configuration related features.

Revision History

This section summarizes the changes in each revision of this guide.

December 2008 Revision

This is the first revision of this guide. This guide is valid for software release v0.2.0.3.

«
...
5
6
7
8
9
...
»

Summary of Contents for OD200-IDU



















































































































Reviews:

No comments

Related manuals for OD200-IDU

Brand: EchoLife Pages: 16

Mediant 1000 MSBG

Brand: AudioCodes Pages: 160

Brand: Media5 Pages: 54

MultiConnect Conduit

Brand: Multitech Pages: 37

Brand: M-system Pages: 7

Air Live SG-101

Brand: Ovislink Pages: 18

WPC-832-2-Modbus-MQTT

Brand: KSH International Pages: 16

OFFICE CONNECT CABLE/DSL SECURE GATEWAY...

Brand: 3Com Pages: 102

Brand: Z-Wave Pages: 68

Brand: Motorola Pages: 28

Brand: Motorola Pages: 351

SURFboard eXtreme SBG6782-AC

Brand: Motorola Pages: 2

Brand: SmartRG Pages: 122

MiBoxer ZB-Box2

Brand: Mi-Light Pages: 6

MULTIVOIP MVP-410ST

Brand: Multitech Pages: 8

MultiVOIP 100 MVP120

Brand: Multitech Pages: 48

Conduit MTCDT-L4E1

Brand: Multitech Pages: 28

Brand: Technicolor Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands