AWB OD200-IDU Operator'S Manual Download Page 42

Page: 42 / 114

Gateway Configuration

5-2

WAN Settings

Select the WAN connection type used by your service provider and specify DNS
(Domain Name System) servers.

Figure 5-1 WAN Settings

The unit can

be connected to your ISP in one of the following ways:

Dynamic IP Address

– Selects configuration for an Internet connection using

DHCP for IP address assignment. This is the default setting.

Static IP Address

– Selects configuration for an Internet connection using a fixed IP

assignment.

L2TP

– Selects configuration for an Internet connection using the Layer 2 Tunneling

Protocol, an access protocol often used for virtual private networks.

PPPoE

– Selects configuration for an Internet connection using the Point-to-Point

Protocol over Ethernet (PPPoE), a common connection method used for DSL
access.

Note:

For the Dynamic IP Address (DHCP) option, the unit requires no further
configuration. Selecting other WAN types displays the parameters that are
required for configuring the connection.

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands