AWB OD200-IDU Operator'S Manual Download Page 90 | Manualshive

Page: 90 / 114

background image

Troubleshooting

A-2

A

• Check that the management station has a valid network connection and that the

Ethernet port that you are using has not been disabled.

• Check the network cabling between the management station and the unit. If the

problem is not resolved, try using a different port or a different cable.

Forgot or Lost the Password

Set the unit to its default configuration by pressing the reset button on the back
panel for 5 seconds or more. Then use the default password “admin” to access the
management interface.

Resetting the Unit

If all other recovery measures fail and the unit is still not functioning properly, take
either of these steps:

• Reset the unit using the web interface, or through a power reset.
• Reset the unit to its factory default configuration by pressing the reset button on the

back panel for 5 seconds or more. Then use the default password “admin” to
access the management interface.

«
...
88
89
90
91
92
...
»

Summary of Contents for OD200-IDU



















































































































Reviews:

No comments

Related manuals for OD200-IDU

Brand: ADTRAN Pages: 5

Brand: Luminext Pages: 8

Intesis IN701-KNX Series

Brand: HMS Networks Pages: 48

Brand: Synway Pages: 7

926 Gateway Light

Brand: Midas Pages: 10

Brand: LifeShield Pages: 2

Brand: Innoband Pages: 131

Brand: Amit Pages: 395

Brand: D-Link Pages: 55

DVG-3104MS - VoiceCenter PSTN Gateway

Brand: D-Link Pages: 3

Brand: D-Link Pages: 7

Brand: D-Link Pages: 9

Brand: D-Link Pages: 7

Brand: D-Link Pages: 7

Brand: D-Link Pages: 7

Brand: D-Link Pages: 92

Brand: D-Link Pages: 56

Brand: D-Link Pages: 71

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands