AWB OD200-IDU Operator'S Manual Download Page 59

Page: 59 / 114

6-1

Chapter 6: WiMAX Settings

The OD200’s WiMAX menu enables you to configure WiMAX connection profiles,
view subscriber station information, and select an operating antenna.

The WiMAX pages include the following options.

Profile Configuration

A profile allows a user to set specific details for connecting to various WiMAX
service providers. The OD200 must have at least one profile configured to be able to
connect to a WiMAX service.

Figure 6-1 WiMAX Profile Configuration

Operator ID

– The ID number that identifies the WiMAX operator for this profile.

(Default: 00:00:02)

Table 6-1 WiMAX Settings

Menu

Description

Page

Profile

Configures WiMAX connection profiles

6-1

SSinfo

Displays subscriber station information for the unit

6-4

Antenna Setting

Configures use of internal or external antennas

6-5

Advance Configure

Configures extended WiMAX features

6-6

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands