AWB OD200-IDU Operator'S Manual Download Page 45

Page: 45 / 114

WAN Settings

5-5

PPPoE Settings

If your service provider supports Point-to-Point Protocol over Ethernet (PPPoE) for
your Internet connection, configure the settings described below.

Figure 5-5 PPPoE Settings

PPPoE Network Server

– The IP address of the PPPoE server, as specified by the

service provider.

Keep Alive

– This option enables the unit to check periodically that the PPPoE

connection is still operating. If the connection is found to be lost, the unit
automatically attempts to reconnect to the service provider. (Default: Enabled)

Keep Alive Time

– The time period the unit waits before checking that the PPPoE

connection is still operating. This parameter only applies when Keep Alive is
enabled. (Default: 60 seconds; Range: 10-180 seconds)

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands