AWB OD200-IDU Operator'S Manual Download Page 37

Page: 37 / 114

Configuration Tools

4-5

Restore Factory Default Configuration

– Resets the unit to its factory default

settings.

Backup Settings/Restore Settings

– When selected, prompts either to backup the

current configuration to a file, or select a previously backed up file to restore to the
unit.

When you select “Restore Factory Default Configuration” and click Apply, a
confirmation page displays. Click the Restore button to continue.

Figure 4-8 Restore Factory Default Configuration

When you select “Backup Settings/Restore Settings” and click Apply, The following
page displays.

Figure 4-9 Backup/Restore Settings

Backup Settings

– Saves the current configuration settings to a file named

“config.bin” on the web management station.

Restore Settings

– Restores a saved configuration file to the unit. You can use the

Browse button to locate the file on the web management station.

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands