AWB OD200-IDU Operator'S Manual Download Page 50

Page: 50 / 114

Gateway Configuration

5-10

The more common TCP service port numbers include: HTTP: 80, FTP: 21, Telnet:
23, and POP3: 110.

Figure 5-10 Virtual Server

Private IP

– The IP address of the server on the local Ethernet network. The

specified address must be in the same subnet as the OD200 and its DHCP server
address pool. (Range: 192.168.1.1 to 192.168.1.254)

Private Port

– Specifies the TCP/UDP port number used on the local server for the

service. (Range: 0-65535)

Type

– Specifies the port type. (Options: TCP or UDP; Default: TCP)

Public Port

– Specifies the public TCP/UDP port used for the service on the WAN

interface. (Range: 0-65535)

Enabled

– Enables the virtual server mapping on the specified ports.

(Default: Disabled)

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands