AWB OD200-IDU Operator'S Manual Download Page 35

Page: 35 / 114

Administrator Settings

4-3

•

DHCP Server

– Displays the DHCP server status.

•

Firewall

– Displays the firewall status.

Figure 4-4 System Status – Information

INFORMATION

– Displays the number of connected clients, as well as the unit’s

LAN and WAN MAC addresses:
•

Connected Clients

– Displays the number of connected clients, if any.

•

Runtime Code Version

– Displays the runtime code version.

•

LAN MAC Address

– Displays the LAN MAC address.

•

WAN MAC Address

– Displays WAN MAC address.

Administrator Settings

The Administrator Settings page enables you to change the default password for
management access to the gateway.

Figure 4-5 Setting a Password

Current Password

– You need to first enter your current administrator password to

be able to configure a new one. (Default: admin)

New Password

– Enter a new administrator password. (Range: 3~12 characters)

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands