AWB OD200-IDU Operator'S Manual Download Page 44

Page: 44 / 114

Gateway Configuration

5-4

L2TP Settings

If your service provider supports Layer 2 Tunneling Protocol (L2TP) for your Internet
connection, configure the settings described below.

Figure 5-4 L2TP Settings

User Name

– Enter your user name for connecting to the L2TP service, as supplied

by the service provider. (Range: 1-32 characters)

Password

– Specify the password for your connection, as supplied by the service

provider. (Default: No password)

L2TP Network Server

– The IP address of the L2TP server, as specified by the

service provider.

Keep Alive

– This option enables the unit to check periodically that the L2TP

connection is still operating. If the connection is found to be lost, the unit
automatically attempts to reconnect to the service provider. (Default: Enabled)

Keep Alive Time

– The time period the unit waits before checking that the L2TP

connection is still operating. This parameter only applies when Keep Alive is
enabled. (Default: 60 seconds; Range: 10-180 seconds)

Summary of Contents for OD200-IDU



















































































































Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands

AWB OD200-IDU, Operator'S Manual

Search results

Summary of Contents for OD200-IDU

Reviews:

Related manuals for OD200-IDU

Brands by name

Popular brands