- 58 -
Teleph. options
ENT
Dial tone listen
YES
Answer listening
YES
Vocal repetition
2 (0 .. 16)
Attempts pause
60 (0:255 sec)
Num. rings answer
0 (0 .. 16)
Telephone options
Dial tone listen:
ree line tone detection circuit is present inside the telephone; when the line is engaged, it ensures
that the dialling happens only when this is effectively present. In case the detecting of the line tone should be
difficult, like in cases of extensions from switchboards, by choosing the option
“NO”
the free line tone listening
circuit is enabled, favouring the dialling.
The disabling of the free line tone listening circuit makes the analysis of the presence, or not, of the telephone
line less reliable and this may jeopardise the switching of the calls on the GSM channel of the control panel.
Answer listening:
If this function is enabled, the vocal message starts to be transmitted only after the called
User has answered; in this case, the call is considered as
“completed with success”
, therefore, it will not be
repeated to the set number if the first repetitive cycle is at least heard, or the call is voluntarily interrupted by the
user by pressing key “4” or key 3 from the telephone receiving the message.
By not enabling this function, the message will start as soon as the dialler will have stopped dialling the telephone number
and the vocal calls will be repeated for all “number of attempts” programmed for all entered numbers (see “Attempts “)
N.B.: By setting NO, the unit no longer complies with EN50131.
Autoanswer machine:
Should an answering machine be included, the overlapping can be activated (see “RTC
Function”).
Download w/o callb:
If this function is enabled, the control panel accepts the remote re-programming directly
without recalling towards the PC.
Attempts pause:
Should the calls not be completed successfully, the delay programmed here will be interposed
between the second attempt and every subsequent attempt towards the same telephone number.
It must be noted that, according to regulation, a minimum pause of 6 seconds is automatically inserted between successive calls.
Vocal repetition:
It defines how many times the eventual vocal message must be repeated when a telephone
communication is activated.
In case of wanting to communicate the message to a
fixed
or
mobile answering machine
, we recommend setting
a sufficient number of repetitions, such to guarantee the recording of the message on the answering machine.
Num.rings answer:
By enabling the Reply Rings function with a number of rings greater than 0, it is possible
to call the system where the control panel is installed to obtain an RTC connection (see “User RTC Functions”).
Slow DTMF dial:
By enabling the Slow DTMF numeration function, the slow composition of the tones of the
telephone numbers called is activated.
Stop dig. calls:
Enabling the function, after a successful telephone call to a digital number the central control unit
blocks further calls to the other digital numbers memorised with the same protocol.
Enable RTC by GSM:
By enabling this function, the system responds in the GSM channel after 3 rings
SMS limiter:
Defines maximum number of SMS to be sent in an interval of 1 hour. By entering 0 it is disabled,
otherwise the control panel sends maximum that number of SMS in one hour and then memorises an event of
“STOP SMS LIMIT N.”. Starts sending again after an hour has passed from the sending of the first SMS of the series.
Press
(CLR)
to vary
Enter the telephone number
Press
(
)
and
(
)
to move
Press
(ENT)
to confirm
Autoansw. machine
NO
Dload w/o callb
NO
Slow DTMF dial
NO
SMS limiter
0 (0 .. 255)
Enab. RTC by GSM
NO
Stop dig. calls
NO
Dialler
XGSM
XGSM
ENT
PIN
0000
SIM credit ctrl.
YES
PIN:
Enter the valid PIN code of the SIM card.
If the PIN code has been disabled this parameter is ignored.
SIM Credit ctrl:
If this function is enabled, the control panel will check the credit of the SIM Card. Should a
rechargeable card be installed, leave “NO”.
GPRS:
The parameters for data connection via XGSM are programmed in this menu
APN (Access Point Name):
Name of the access point (server) to which a mobile device will try to connect to
gain access to the Internet to make data transfers.
APN:
Access point name. If left blank, the panel will use the default names made available by the network
operator used (valid only for Italy): TIM: ibox.tim.it, VODAFONE: web.omnitel.it, WIND: internet.wind
Username:
user name for accessing the APN (if required by the operator)
Password:
password for accessing the APN (if required by the operator)
GPRS
ENT
APN
ENT
APN
Username
Password
Press
(CLR)
to vary
Writing keys:
(1)
abc1
(2)
def2
(3)
ghi3
(4)
jkl4
(5)
mno5
(6)
pqr6
(7)
stu7
(8)
vwx8
(9)
yz.
(0)
_’0
Press
(ENT)
to confirm
Press arrows
(
)
and
(
)
to position the cursor
Press
(ESC)
to go back
Press
(
)
and
(
)
to move
to following
page
from previus
page
