- 55 -
Tel. num. #
1 (1 .. 16)
Telephone numbers
Telephone number:
Select the telephone number to be programmed from 1 to 16.
Telephone Number 1:
Set the wanted telephone number
The letter
P
on PSTN interface ensures that the dialler interprets the number before this initial as necessary for
getting an external line from a switchboard (Ex.:
9P049W334312
).
The letter
W
introduces a three seconds pause where it has been included (Ex.:
049W334312
).
The listening of the free line tone, if enabled, starts after selection of part of the number before the P code.
If the interface in use is GSM, all digits before the symbols P and W, are omitted from the selection.
Note:
The letters
P
and
W
, are set by scrolling with the arrows
(
)
and
(
)
and by confirming the data by pressing
the arrow
(
)
Email:
Set the email address to send the messages to. Requires both the
EWEB/EWEB WIFI
optional board to be
installed and the WEB interface to be set.
Protocol:
defines, for every telephone profile, the modality with which the events must be transmitted.
-
VOCAL:
it is the protocol that is normally used to communicate the alarm messages in vocal.
- FAST FORMAT:
this is a protocol that allows alarm and technical events to be communicated to special receivers
installed at Security Firm headquarters
- SIA1:
this is a protocol that allows alarm and technical events to be communicated to special receivers installed
at Security Firms, more advanced compared to the FAST FORMAT.
- SIA2:
this is a protocol that allows alarm and technical events to be communicated to special receivers installed
at Security Firms, more advanced compared to the FAST FORMAT.
- SIA-HAYES:
it is a more advanced protocol than SIA that allows alarm and technical events to be communicated
to an AVS-certified modem connected to a PC on which the WINREC. reception software is installed.
- CONTACT-ID:
this is a protocol that allows alarm and technical events to be communicated to special receivers
installed at Security Firms, more advanced compared to the FAST FORMAT.
- SMS/Email:
this is the protocol that allows alarm or technical events to be communicated either via SMS (in this
case it requires both the optional XGSM board to be installed and the GSM interface to be set) or via email (in
this case it requires the optional XWEB/EWEB board to be installed and the WEB interface to be set).
Interface:
Set the wanted interface towards which the calls are to be forwarded
- PSTN:
Select PSTN if wanting to forward calls only on analogical line
- GSM:
Select GSM if wanting to forward the call only on GSM channel using the Xgsm.
- PSTN/ backup GSM:
Select PSTN/ backup GSM if wanting to forward the call on PSTN line and use the GSM
channel only if the analogical line is absent.
The switching to GSM happens after verification of the absence of line voltage and/or analysis of the Dial tone
(only if “Free line listening at YES” is set).
Note:
the call will be repeated in GSM if the same has not had a good result in PSTN.
- PSTN + GSM:
Select PSTN + GSM if wanting to forward the call on both analogical line and on GSM channel
- GPRS/IP:
Select GPRS/IP if wanting to forward the call on the GSM line to a receiver set to the SIA - IP protocol
(supports protocols SIA1, SIA2 and CONTACT ID)
- WEB:
Select WEB to send the call via the IP network to a receiver that is compatible with the SIA - IP protocol
supports SIA1, SIA2 and CONTACT ID protocols) or to communicate events via email.
Press
(CLR)
to vary
Press
(ENT)
to confirm
Press
(
)
or
(
)
to move
Press
(ESC)
to go back
In this menu it is possible to memorise up to 16 telephone numbers. For every telephone number, it is possible to define the communication
protocol (Vocal, Fast, Sia 1st lev., Sia 2nd lev., Sia_Hayes, Contact-Id), the number of call attempts for every Tel. Num., with which interface
(PSTN/GSM) the calls are forwarded and if the main, the Partition and the additional phone must be communicated (for vocal protocols).
Small programming steps:
- Set existence of the telephone in the installation menu; PSTN ENABLING: YES and/or GSM ENABLING: YES
- Set a communication protocol; ex: VOCAL
- Set a telephone number to call; in
“telephone number”
- ex: 049 9698 ...
- Set the communication interface: ex PSTN if using the telephone integrated on telephone line, GSM if using module Xgsm.
- Associate a user to the set telephone number to give the number the user features (RTC - Calls block - Number recognition); leave 0
(zero) if no association is wanted.
- Associate the zones that will have to be communicated to the telephone number. - ZONES
- Associate the technical events that will have to be communicated to the telephone number. - ASSOCIATE EVENTS
- Associate the telephone numbers to the active Partitions. - “ASSOCIATE PARTITIONS”
Definition of “interface”:
physical mean with which a call is made.
Definition of “protocol”:
information distribution modality
Dialler
ENT
Dialler
Teleph. numbers
ENT
Tel. num. #
Protocol
VOCAL
Interface
PSTN
to following
page
from previus
page
