- 50 -
WL / XSATHP satellites
WL/XSATHP satellite:
By accessing in this menu there is the possibility of programming the sensors via
radio and the sensors addressed performing the acquisition, the deletion and the signal verifications for
every acquired sensor.
Note:
all references to the detectors are to be considered relating to the address selected on the detector
with the Dip and not to the zone belonging in control panel.
CAUTION: using these peripherals voids compliance with EN50131
Sensor modify:
in this menu the acquisition and deletion of the detectors via radio per satellite is programmed.
Satellite addr.
(Satellite address): select the satellite on which the acquisition or deletion of the detectors
procedure is to be carried out
Satellite via Radio:
Sens. Acquisition
(detectors acquisition): by accessing this menu the acknowledgement procedure of the
various detectors activates for 60 seconds.
Sens(n) Sat(n)
(sensor num.; satellite num.): these are the references for understanding which satellite via
radio has received, which detector has transmitted and to which control panel zone it is coupled.
Signal received:
the amount of signal received from the sat-radio is highlighted on a bar from 1 to 8.
Sensor deletion
(detectors deletion): by accessing this menu there is the possibility of individually deleting
the various acquired detectors.
All deletion:
by accessing this menu there is the possibility of simultaneously deleting all acquired detectors.
Once deletion is completed, the display visualises “executed”.
Satellite XSATHP:
Detector memorization :
get into this menu to activate for a period of 1 minute the learning process of
sensors connected to the selected satellite. After this period, the keyboard will intermittently the type of
sensor connected to the satellite and its corresponding address.
Sn (n)
(detector number)
Sat (N)
(satellite number)
Outspider / BMHP / XSATMINI
(sensor type): This is
the way to identify which sensors have been memorized, on which satellite and detector type.
Detector Elimination:
not supported function
Total elimination
(elimination of all detectors): not supported function
NB:
to make the elimination of one or more detectors, disconnect the sensor to remove from its serial port,
and then perform the detector memorization again.
Sensors verify: in this menu there is the possibility of checking which detectors have been effectively
acquired by the satellite via radio and test them.
Sensors list
: the acquired detectors are highlighted with a (Y)
Sensors test:
checks which satellite via radio has received, which detector has transmitted and to which
control panel zone this is coupled. For XSATHP satellites, such as occurs sensors were acquired, from
which the satellite and the sensor type.
Satellite via Radio: Sens(n)
(Sensor num.)
Sat(n)
(Satellite num.)
Signal received
(signal quality): see
“Sens. Acquisition”
Note:
to
include a pad
of virtual signal, press
(CLR)
once. The pad will be active only during the test, not
during the normal functioning of the system. In keypad, as well as the visualisation
Sat(n) Dt(n) Zn(n)
, an
“A”
will appear
Note: to activate the memorisation of the radio detectors,
press the MEM key in “detectors test” modality.
This function displays a list of detectors received with valid power level.
To exit memorisation, press
MEM.
Satellite XSATHP: Sn(n)
(Sensor num.)
Sat(n)
(Satellite num.)
Outspider/BMHP/XSATMINI
(Sensor
type): see
“Sens. Acquisition”
ATTENTION
Programming steps corresponding to the BIP remote control and EEPROM cancellation are active
only for programming the radio satellite. The submenus are also present in the XSATHP satellite
menu but are not programmable.
Remote Controls Acquisition
It is possible to acquire up to sixteen (16) remote controls for every group (max. 4) that must be coded
following the table attached to BIP. It is not possible to acquire more remote controls with the same coding
in the same group and we recommend not acquiring the same remote control on more groups.
To acquire a remote control, transmit from near the receiver, bearing in mind that the
ACQUISITION
happens
by pressing
any key, with the exception of key (5)
.
Amends Remote Controls: the acquisition and deletion of the remote controls is programmed in this menu.
Satellite add.(Satellite address):
select the satellite on which the acquisition or deletion procedure is to
be carried out.
Delete Eeprom:
by accessing this menu there is the possibility of simultaneously deleting all acquired
detectors and remote controls. Once deletion is completed, the display visualises
“performed”
.
Press
(CLR)
to vary
Write the number to be set
Press
(
)
and
(
)
to move
Press
(ENT)
to confirm
Sensors list
ENT
Sensors test
ENT
Sensors verify
ENT
Sensors list 1
YYYYYYYYYYYYYYYY
Sens(n) Sat(n)
signal received
BIP modify
ENT
Sat(n) G(n)TCM(n)
signal received
All deletion
ENT
Are you sure...??
CLR=NO YES=ENT
Lista BIP 1
nnnnnnnnnnnnnnnn
BIP verify
ENT
Sat(n) G(n) TCM(n)
signal received
BIP Acquisition
ENT
BIP Deletion
ENT
BIP #
1 (1 . . 64)
Group number
1 (1 . . 4)
BIP list
ENT
BIP test
ENT
Eeprom deletion
ENT
Are you sure...??
CLR=NO YES=ENT
All deletion
ENT
Sensor deletion
1 (max. 32)
Sens(n) Sat(n)
signal received
Sens. acquisition
Sensors deletion
ENT
Sens. acquisition
ENT
Sensor modify
ENT
Satellite addr.
1 (1 . . 8)
WL/XSATHP satell
ENT
Numero gruppo
to following
page
from previus
page
