Avaya Cajun P333T User Manual Download Page 89

Page: 89 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

show ppp incoming timeout

Use the

ppp incoming timeout

command to see the amount of time in minutes

that a PPP session can remain idle before being automatically disconnected.

The syntax for this command is:

show ppp incoming timeout

Output Example:

P330-N> show ppp incoming timeout

PPP incoming timeout is 10 minutes

show ppp baud-rate

Use the s

how ppp baud-rate

command to display the set baud-rate.

The syntax for this command is:

show ppp baud-rate

Output Example:

P330-N> show ppp baud-rate

PPP baud rate is 38400

show ppp configuration

Use the s

how ppp configuration

command to display the ppp configuration

The syntax for this command is:

show ppp configuration

Output Example:

P330-N> show ppp configuration

PPP baud rate is 38400

PPP incoming timeout is 0 minutes

PPP Authentication Parameters:

------------------------------

Incoming: None

Summary of Contents for Cajun P333T























































































































































































Search results

Summary of Contents for Cajun P333T

Reviews:

Avaya Cajun P333T, User Manual, Page: 89 / 182

Search results

Summary of Contents for Cajun P333T

Reviews: