manualshive.com logo in svg

Avaya Cajun P333T, User Manual, Page: 57 / 182

Share
Download
Avaya Cajun P333T User Manual Download Page 57

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

41

clear screen

The clear screen command clears the current terminal display.

The syntax for this command is:

clear screen

ping

Use the

 ping 

command to send ICMP echo request packets to another node on the 

network.

The syntax for this command is:

ping [host[number]]

Note:  

You can use this command via the Master switch only.

Output Example:
To ping the IP number 149.49.48.1 four times:

P330-N> ping 149.49.48.1 4

PING 149.49.48.1: 56 data bytes

64 bytes from 149.49.48.1: icmp_seq=0. time=0. ms

64 bytes from 149.49.48.1: icmp_seq=1. time=0. ms

64 bytes from 149.49.48.1: icmp_seq=2. time=0. ms

P330-1(super)#  64 bytes from 149.49.48.1: icmp_seq=3. time=0. ms

----149.49.48.1 PING Statistics----

4 packets transmitted, 4 packets received, 0% packet loss

round-trip (ms)  min/avg/max = 0/0/0

host

Host IP address/Internet address of route destination. If missing 
then the last host IP is used.

number

Number of packets to send. If missing, then the last number is used. 
If the last number is not available, the default is 4.

Summary of Contents for Cajun P333T























































































































































































Reviews:

No comments