manualshive.com logo in svg

Avaya Cajun P333T, User Manual, Page: 27 / 182

Share
Download
Avaya Cajun P333T User Manual Download Page 27

Chapter 3

Avaya P333T Front and Back Panels

Avaya P333T User’s Guide

11

Avaya P330 Back Panel

The Avaya P330 back panel contains a stacking sub-module slot, power supply and 
BUPS connector. Figure 3.3 shows the back panel of the AC switch (top) and the DC 
switch (bottom) with a stacking sub-module installed.

Figure 3.3

Avaya P330 AC and DC Back Panels

Note:  

Further illustrations of the Avaya P330 Back Panel will be that of the AC 

model, the topmost panel in Figure 3.3.

Figure 3.3 shows the back panel of the AC switch (top) and the DC switch (bottom) 
with a stacking sub-module installed.

BUPS Input Connector

The BUPS input connector (see Figure 3.4) is a 5 VDC connector for use with the 
Avaya P330 BUPS unit only. A BUPS Input sticker appears directly to the right the 
BUPS input connector.

Figure 3.4

BUPS Input Connector Sticker

BUPS Input

Summary of Contents for Cajun P333T























































































































































































Reviews:

No comments