manualshive.com logo in svg

Avaya Cajun P333T, User Manual, Page: 63 / 182

Share
Download
Avaya Cajun P333T User Manual Download Page 63

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

47

show download status

Use the 

show download status

 command to display a summary of the last 

software download operation.

The syntax for this command is:

show download status [slot]

Output Example:

P330-1(super)# sh download status 1

Mod   Bank   Download State  Activity Status   Download Size

----- ------ --------------- ---------------- ---------------

1.    Bank B   idle          Download idle      0

Mod   Version   Host          File

----- --------- ------------- ------------------

1.    3.5.18    149.49.70.61 d:\p340sw\gt-ml\3.5.18\p332gt_ml

Note:  

This command is only supported by the P332G-ML and P332GT-ML switches.

show snmp

Use the

 show snmp 

command to display SNMP information.

The syntax for this command is:

show snmp

Output Example:

P330-N> show snmp

Authentication trap disabled

Community-Access     Community-String

----------------     ----------------

read-only            public

read-write           public

trap                 public

Trap-Rec-Address     Traps Enabled

----------------     ----------------

1.1.1.1              config

                     fault

etc...

Summary of Contents for Cajun P333T























































































































































































Reviews:

No comments