manualshive.com logo in svg

Avaya Cajun P333T, User Manual, Page: 42 / 182

Share
Download
Avaya Cajun P333T User Manual Download Page 42

Chapter 4

Installation and Setup

26

Avaya P333T User’s Guide

Configuring the Switch

The Avaya P330 may be configured using the text-based Command Line Interface 
(CLI), the built-in Avaya P330 Device Manager (Embedded Web) or Avaya Multi-
Service Network Manager™.
For instructions on the text-based utility, see the CLI chapter.
For instructions on installation of the graphical user interfaces, see the Avaya P330 
Device Manager Appendix. For instructions on the use of the graphical user 
interfaces, refer to the Device Manager User’s Guide on the Documentation and 
Utilities CD.

Avaya P330 Default Settings

The default settings for the Avaya P330 switch and its ports are determined by the 
Avaya P330 software. These default settings are subject to change in newer versions 
of the Avaya P330 software. See the Release Notes for the most up-to-date settings.

Table 4.1

Default Switch Settings 

Function

Default Setting

IP address

149.49.32.134

Default gateway

0.0.0.0

VLANs

VLAN 1

Spanning tree

Enabled

Bridge priority for Spanning Tree

32768

Time server IP address

0.0.0.0

Timezone offset

0 hours

Read-only SNMP community string

Public

Read-write SNMP community string

Public

Trap SNMP community string

Public

SNMP retries number

3

SNMP timeout

2000 Seconds

SNMP authentication trap

Disabled

CLI timeout

15 Minutes

User Name/Password

root/root

Summary of Contents for Cajun P333T























































































































































































Reviews:

No comments