Avaya Cajun P333T User Manual Download Page 77

Page: 77 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

Output Fields

Field

Description

Port

Switch and port number

Send-
Flowcontrol-
Admin

Send flow-control administration. Possible settings:
• ON indicates that the local port is allowed to send flow

control frames to the far end.

• OFF indicates that the local port is not allowed to send flow

control frames to the far end.

Send-
Flowcontrol-
Oper

Send flow-control operation mode. Possible modes:
• ON indicates that the local port will send flow control frames

to the far end.

• OFF indicates that the local port will not send flow control

frames to the far end.

Receive-
Flowcontrol-
Admin

Receive flow-control administration. Possible settings:
• ON indicates that the local port will act upon flow control

indications if received from the far end.

• OFF indicates that the local port will discard flow control

frames if received from the far end.

Receive-
Flowcontrol-
Oper

Receive flow-control operation mode. Possible modes:
• ON indicates that the local port will act upon flow control

indications received from the far end.

• OFF indicates that the local port will discard flow control

frames received from the far end.

Summary of Contents for Cajun P333T























































































































































































Search results

Summary of Contents for Cajun P333T

Reviews:

Avaya Cajun P333T, User Manual, Page: 77 / 182

Search results

Summary of Contents for Cajun P333T

Reviews: