Avaya Cajun P333T User Manual Download Page 103

Page: 103 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

Output Example:

P330-N# clear port mirror 1/2/1/4

this command will delete the port mirror entry

- do you want to continue (Y/N)? y

Mirroring packets from port 1/2 to port 1/4 is cleared

clear secure mac

Use the

clear secure mac

command to remove a MAC address from the CAM

table of a secured port.

Note:

This command is not supported by the P330-ML switches.

The syntax for this command is:

clear secure mac <mac-address> port <mod-num>/<port-num>

Output Example:

P330-N> clear secure mac 1-2-3-4-5 port 1/17

01-02-03-04-05 cleared from secure address list for port 1/17

Note:

If this command is to be implemented on a switch other than the stack master,

a session should be opened to the relevant switch.

Summary of Contents for Cajun P333T























































































































































































Search results

Summary of Contents for Cajun P333T

Reviews:

Avaya Cajun P333T, User Manual, Page: 103 / 182

Search results

Summary of Contents for Cajun P333T

Reviews: