manualshive.com logo in svg

Avaya Cajun P333T, User Manual, Page: 105 / 182

Share
Download
Avaya Cajun P333T User Manual Download Page 105

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

89

• set port disable

Administratively disables a port.

Page 100

• set port speed

Sets the speed for a 10/100 port.

Page 101

• set port duplex

Sets the duplex mode of a port.

Page 101

• set port name

Assigns a name to a port.

Page 102

• set port trap

Enables/disables the SNMP up/down 
link traps sent for port.

Page 102

• set port vlan

Assigns the Port VLAN ID (PVID).

Page 102

• set  port  vlan-binding-

mode

Defines the port binding method.

Page 103

• set port static-vlan

Defines a multiple VLANs per port.

Page 103

• set port self-loop 

discovery 
Admin_Status

Defines a port’s IBM token ring 
discovery mode.

Page 104

• set port channel

Defines a LAG interface.

Page 104

• set port classification

Defines port classification.

Page 105

• set  port  redundancy 

on/off

Defines/deletes a link redundancy 
entry.

Page 106

• set port redundancy

Enables/disables all the defined link 
redundancy schemes.

Page 106

• set internal buffering

Sets internal buffering capacity to 
maximum/minimum.

Page 107

• set boot bank

Configures the boot bank from which 
the switch will boot.

Page 107

• set intermodule port 

redundancy

Defines the stack’s unique fast 
redundancy scheme.

Page 108

• set intermodule port 

redundancy off

Clears the intermodule redundancy.

Page 108

• set port mirror

Sets a port mirroring source-destination 
pair in the stack.

Page 109

• set port spantree

Enables or disables the spanning tree for 
switch ports.

Page 109

• set  port  spantree 

priority

Sets the port spantree priority level.

Page 110

Summary of Contents for Cajun P333T























































































































































































Reviews:

No comments