Avaya Cajun P333T User Manual Download Page 65

Page: 65 / 182

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

The syntax for this command is:

show logout

Output Example:

P330-N> show logout

CLI timeout is 10 minutes

show interface

Use the

show interface

command to display information on network

interfaces.

The syntax for this command is:

show interface

Output Example:
To display the interface:

P330-N> show interface

Interface Name VLAN IP address Netmask

-------------- ---- --------------- ---------------

inband 1 10.0.0.1 255.255.255.0

ppp disable 1 0.0.0.0 0.0.0.0

show device-mode

Use the

show device-mode

command to show the P332G-ML/P332GT-ML/

P333R/P333R-LB operating mode you are currently in. Possible modes are Router,
or Switch.

Note:

This command is not supported by the P333T/P334T/P332MF/P333T-PWR

switches which do not have Router mode.

The syntax for this command is:

show device-mode

Summary of Contents for Cajun P333T























































































































































































Search results

Summary of Contents for Cajun P333T

Reviews:

Avaya Cajun P333T, User Manual, Page: 65 / 182

Search results

Summary of Contents for Cajun P333T

Reviews: