manualshive.com logo in svg

Avaya Cajun P333T, User Manual, Page: 53 / 182

Share
Download
Avaya Cajun P333T User Manual Download Page 53

Chapter 5

Avaya CLI – Architecture, Access & Conventions

Avaya P333T User’s Guide

37

Universal Commands

Universal commands are commands that can be issued anywhere in the hierarchical 
tree. 

Top and Up commands

The 

Up

 command moves you up to the next highest level in the CLI command 

hierarchy. The 

Top

 command moves you to the highest level.

Retstatus command

Use the

 retstatus 

command to show whether the last CLI command you 

performed was successful. It displays the return status of the previous command.
The syntax for this command is:

 retstatus

Output Example:

P330 # set port negotiation 2/4 disable

Link negotiation protocol disabled on port 2/4.

Tree command

The

 tree 

command displays the commands that are available at your current 

location in the CLI hierarchy.
The syntax for this command is:

 tree

Summary of Contents for Cajun P333T























































































































































































Reviews:

No comments