manualshive.com logo in svg

Avaya Cajun P333T, User Manual, Page: 107 / 182

Share
Download
Avaya Cajun P333T User Manual Download Page 107

Chapter 6

CLI – Layer 2

Avaya P333T User’s Guide

91

set logout

The

 set logout 

command is used to set the number of minutes until the system 

automatically disconnects an idle session.

The syntax for this command is:

set logout <timeout>

 

Output Example:
To set the number of minutes until the system disconnects an idle session 

• set intelligent-multicast 

router-port-pruning 
time

Sets the aging time for router ports.

Page 119

• set intelligent-multicast 

group-filtering-delay 
time

Sets the time delay before a filter is 
applied to a specific group.

Page 119

• set secure mac

Adds a unicast MAC address into the 
CAM table of a secured port.

Page 119

• set security mode

Enables or disables the stack’s MAC 
security.

Page 120

• set arp-aging-interval

Sets the ARP aging interval.

Page 120

• set arp-tx-interval

Sets the keep-alive interval.

Page 120

• set self-loop-discovery 

Admin_Status

Sets the IBM token ring discovery mode.

Page 121

• set welcome message 

Sets a welcome message to appear after 
a reboot.

Page 121

• set allowed managers 

enabled/disabled

Enables/disables the Allowed Managers 
feature.

Page 122

• set allowed managers 

IP

Used to add or remove an IP address 
from the allowed managers table.

Page 122

• set psu type 

Sets the main power supply type (AC/
DC) of the module.

Page 122

timeout

Number of minutes (0 to 999) until the system automatically 
disconnects an idle session. Setting the value to 0 disables the 
automatic disconnection of idle sessions (default is 15 minutes).

Summary of Contents for Cajun P333T























































































































































































Reviews:

No comments