manualshive.com logo in svg

ARM Cortex-R4, Technical Reference Manual

The ARM Cortex-R4 Technical Reference Manual is a comprehensive manual providing detailed information and specifications about this product. It is available for free download on manualshive.com, where users can easily access this valuable resource to enhance their understanding and optimize their usage of the ARM Cortex-R4.

Share
Download
background image

Signal Descriptions 

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

A-3

ID073015

Non-Confidential

A.2

Global signals

Table A-1

 shows the processor global signals.

The free clock is ungated, with minimal insertion delay, because it clocks the clock gating 
circuits. Therefore, you must ensure that incoming clocks are balanced with the free clock.

Table A-1 Global signals

Signal

Direction

Clocking

Description

FREECLKIN

Input

-

Free version of the core clock.

CLKIN

Input

-

Core clock.

CLKIN2

Input

-

Core clock, in phase with 

DUALCKLIN

, for configurations 

with dual-redundant core.

a

nRESET

Input

Any

Core reset.

nSYSPORESET

Input

Any

System power on reset.

nCPUHALT

Input

Any

Processor halt after reset.

DBGNOCLKSTOP

Input

Any

Processor does not stop the clocks when entering WFI state.

a

DUALCLKIN

Input

-

Clock for second, redundant, core.

a

DUALCLKIN2

Input

-

Clock for second, redundant, core, in phase with 

CLKIN

.

a

STANDBYWFI

Output

FREECLKIN

Indicates that the processor is in Standby mode and the 
processor clock is stopped. You can use this signal for TCMs 
RAM clock gating.

a. Not available in r0px revisions of the processor.

Summary of Contents for Cortex-R4





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-R4

MAGIMIX Mini Plus User Manual preview
Mini Plus
Brand: MAGIMIX Pages: 84
Beper 90312 Use Instructions preview
90312
Brand: Beper Pages: 36
Springlane 943621 Instruction Manual preview
943621
Brand: Springlane Pages: 88
Lebensstil Kollektion LKCB-4112SS Instruction Manual preview
LKCB-4112SS
Brand: Lebensstil Kollektion Pages: 8
EPV Polar Max Recessed Series Installation Manual preview
Polar Max Recessed Series
Brand: EPV Pages: 8
Suntec Wellness SPI-8380 veggie noodle Instruction Manual preview
SPI-8380 veggie noodle
Brand: Suntec Wellness Pages: 38
Ultra VARIO PLUS 750 Instruction Manual preview
VARIO PLUS 750
Brand: Ultra Pages: 16
Premier PBM-501L Installation Instructions preview
PBM-501L
Brand: Premier Pages: 2
Hyundai UM 210 Instruction Manual preview
UM 210
Brand: Hyundai Pages: 60
Kverneland FHS 155 Technical & Service Manual preview
FHS 155
Brand: Kverneland Pages: 54
Silvercrest SMZE 500 C2 Operating Instructions Manual preview
SMZE 500 C2
Brand: Silvercrest Pages: 52
Silvercrest SMZ CD 400 A 1 Operating Instructions Manual preview
SMZ CD 400 A 1
Brand: Silvercrest Pages: 49
Silvercrest SMZE 500 A1 Operating Instructions Manual preview
SMZE 500 A1
Brand: Silvercrest Pages: 63
Silvercrest SMZCD 400 A1 Operating Instructions Manual preview
SMZCD 400 A1
Brand: Silvercrest Pages: 63
Silvercrest MONSIEUR CUISINE CONNECT Operating Instructions Manual preview
MONSIEUR CUISINE CONNECT
Brand: Silvercrest Pages: 40
Silvercrest 281064-B Operating Instructions Manual preview
281064-B
Brand: Silvercrest Pages: 19
Silvercrest 322511 1901 Operating Instructions Manual preview
322511 1901
Brand: Silvercrest Pages: 34
Silvercrest 288402 Operating Instructions Manual preview
288402
Brand: Silvercrest Pages: 75

Brands by name

Popular brands

Load more brands