ARM Cortex-R4 Technical Reference Manual Download Page 282 | Manualshive

Page: 282 / 436

background image

Debug

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

12-8

ID073015

Non-Confidential

12.3.5

Memory addresses for breakpoints and watchpoints

The

Vector Catch Register

(DBGVCR) sets breakpoints on exception vectors as instruction

addresses.

The

Watchpoint Fault Address Register

(DBGWFAR) reads an address and a processor state

dependent offset, +8 for ARM and +4 for Thumb.

12.3.6

Power domains

The processor has a single power domain. Therefore, it does not support the Event Catch
Register, the OS Lock, or the OS Save and Restore functionality.

12.3.7

Effects of resets on debug registers

The processor has two reset signals that affect the debug registers in the following ways:

nSYSPORESET

You must assert this signal when powering up to set the non-debug processor
logic to a known state.

PRESETDBGn

You can assert this signal to set all of the debug logic to a known state, without
affecting the state of the remainder of the processor logic.

12.3.8

APB port access permissions

The restrictions for accessing the APB slave port are described as follows:

Privilege of memory access

You must configure the system to disable accesses to the memory-mapped
registers based on the privilege of the memory access.

Power down

The processor only supports a single power domain, therefore you must configure
the system to return an error response to all accesses made to the APB interface
while the processor is powered-down.

Privilege of memory access permission

When non-privileged software attempts to access the APB slave port, the system must ignore
the access or generate an error response to the access. You must implement this restriction at the
system level because the APB protocol does not have a privileged or user control signal. You
can choose to have the system either ignore the access or generate an error response.

You can place additional restrictions on memory transactions that are permitted to access the
APB port. However, ARM does not recommend this.

«
...
280
281
282
283
284
...
»

Summary of Contents for Cortex-R4





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-R4

Brand: Canon Pages: 6

7215 - LV XGA LCD Projector

Brand: Canon Pages: 8

Brand: NAD Pages: 55

Brand: Oster Pages: 16

Brand: Steg Pages: 10

Brand: Garland Pages: 124

Brand: Premier Mounts Pages: 1

Brand: Silvercrest Pages: 46

Brand: Outlaw Pages: 47

Brand: Kompernass Pages: 44

Brand: wowvision Pages: 21

Brand: ViewSonic Pages: 20

myViewBoard Direct

Brand: ViewSonic Pages: 24

Brand: ViewSonic Pages: 39

Brand: King Edward Pages: 16

Brand: Techly Pages: 8

Brand: Techly Pages: 8

FRESH EXPRESS DJ753510

Brand: Moulinex Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands