ARM Cortex-R4 Technical Reference Manual Download Page 133 | Manualshive

Page: 133 / 436

background image

System Control

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

4-63

ID073015

Non-Confidential

shows the ATCM Region Register bit assignments.

To access the ATCM Region Register, read or write CP15 with:

MRC p15, 0, <Rd>, c9, c1, 1

; Read ATCM Region Register

MCR p15, 0, <Rd>, c9, c1, 1

; Write ATCM Region Register

4.3.24

c9, TCM Selection Register

The TCM Selection Register determines the TCM region register that the processor writes to.
The processor only supports one TCM region for each TCM interface, and the TCM Selection
Register Reads-As-Zero and ignores writes. It is only accessible in Privileged mode.

4.3.25

c11, Slave Port Control Register

The Slave Port Control Register characteristics are:

Purpose

•

Enables or disables TCM access to the AXI slave port in Privileged
or User mode.

•

Enables access to the cache RAMs through the AXI slave port. See

c1, Auxiliary Control Register

Usage constraints

The Slave Port Control Register is:
•

a read/write register

•

accessible in Privileged mode only.

Configurations

Available in all processor configurations.

Attributes

Table 4-43 on page 4-64

.

Figure 4-42 on page 4-64

shows the Slave Port Control Register bit assignments.

Table 4-42 ATCM Region Register bit assignments

Bits

Name

Function

[31:12] Base

address

Base address. Defines the base address of the ATCM. The base address must be aligned to the
size of the ATCM. Any bits in the range [(log

2

(RAMSize)-1):12] are ignored.

At reset, if

LOCZRAMA

is set to:

0 = The initial base address is implementation-defined. See

Configurable options

1 = The initial base address is

0x0

.

[11:7]

-

UNP on reads, SBZ on writes.

[6:2]

Size

Size. Indicates the size of the ATCM on reads. On writes this field is ignored. See

About the TCMs

b00000 = 0KB
b00011 = 4KB
b00100 = 8KB
b00101 = 16KB

b00110 = 32KB
b00111 = 64KB
b01000 = 128KB
b01001 = 256KB

b01010 = 512kB
b01011 = 1MB
b01100 = 2MB
b01101 = 4MB
b01110 = 8MB.

[1]

-

SBZ

[0]

Enable

Enables or disables the ATCM.
0 = Disabled
1 = Enabled. The reset value of this field is determined by the

INITRAMA

input pin.

«
...
131
132
133
134
135
...
»

Summary of Contents for Cortex-R4





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-R4

Brand: Cuisinart Pages: 2

Brand: Beem Pages: 52

Brand: Waring Pages: 100

Brand: KitchenAid Pages: 32

Brand: KitchenAid Pages: 4

Brand: KitchenAid Pages: 100

Brand: KitchenAid Pages: 128

Brand: KitchenAid Pages: 209

Brand: KitchenAid Pages: 260

Brand: KitchenAid Pages: 5

Brand: KitchenAid Pages: 3

Brand: Imetec Pages: 38

Brand: EPOX Pages: 70

Kitchen Wizz Peel & Dice SFP820

Brand: Sage Pages: 60

Brand: BSS Audio Pages: 3

Brand: BSS Audio Pages: 8

Brand: Waring Pages: 6

Brand: Lindy Pages: 23

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands