ARM Cortex-R4 Technical Reference Manual Download Page 43 | Manualshive

Page: 43 / 436

background image

Functional Description

ARM DDI 0363G

Copyright © 2006-2011 ARM Limited. All rights reserved.

2-18

ID073015

Non-Confidential

Note

You can enable error checking and 64-bit store behavior on a per-TCM interface basis.
References to these controls relate to whichever TCM is being initialized.

Using TCMs from reset

The processor can be pin-configured to enable the TCM interfaces from reset, and to select the
address at which each TCM appears from reset. See

TCM initialization

for more

information. This enables you to configure the processor to boot from TCM but, to do this, the
TCM must first be preloaded with the boot code. The

nCPUHALT

pin can be asserted while

the processor is in reset to stop the processor from fetching and executing instructions after
coming out of reset. While the processor is halted in this way, the TCMs can be preloaded with
the appropriate data. When the

nCPUHALT

pin is deasserted, the processor starts fetching

instructions from the reset vector address in the normal way.

Note

When it is deasserted to start the processor fetching,

nCPUHALT

must not be asserted again

except when the processor is under processor or power-on reset, that is,

nRESET

asserted. The

processor does not halt if the

nCPUHALT

pin is asserted while the processor is running.

«
...
41
42
43
44
45
...
»

Summary of Contents for Cortex-R4





















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Cortex-R4

Brand: miniDSP Pages: 17

Brand: Premier Mounts Pages: 14

Brand: Rasonic Pages: 26

Brand: Skymsen Pages: 24

Brand: Barco Pages: 13

Micro Line MLC-200

Brand: Lemco Pages: 2

Brand: Brentwood Appliances Pages: 20

Brand: HOME ELEMENT Pages: 9

Brand: Moulinex Pages: 6

NC-58900 FOODPRO1

Brand: Nesco Pages: 21

Brand: Gastroback Pages: 33

Brand: Taurus Pages: 11

Brand: Navitar Pages: 7

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 4

Brand: JVC Pages: 27

Brand: KitchenAid Pages: 80

Brand: KitchenAid Pages: 101

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands