manualshive.com logo in svg

Analog Devices AD9361, Reference Manual

Share
Download
Analog Devices AD9361 Reference Manual Download Page 79

AD9361 Reference Manual 

UG-570 

 

 | Page 79 of 128 

Control Output 3 (CH1 ADC Power Ready) 

If ADC power is used for AGC power measurements, this signal 
will pulse high when a new power word is ready. The 

AD9361

 

internal clock rates determine the pulse durations. The interval 
between updates is set by the Weight ADC Power Multipliers. 

Control Output 2 Through Control Output 0 (CH1 AGC 
State[2:0]) 

See 0x035 = 0x07 Control Output 3 through Control Output 1. 

0x035 = 0x13 (GAIN CONTROL, POWER WORD 
READY) 

Control Output 7 (CH2 Filter Power Ready) 

Same as 0x035 = 0x12 Control Output 7 but applies to Rx2. 

Control Output 6 (CH2 Gain Lock) 

See 0x035 = 0x08 Control Output 2. 

Control Output 5 (CH2 Energy Lost) 

See 0x035 = 0x08 Control Output 1. 

Control Output 4 (CH2 Stronger Signal) 

See 0x035 = 0x08 Control Output 3. 

Control Output 3 (CH2 ADC Power Ready) 

Same as 0x035 = 0x12 Control Output 3 but applies to Rx2. 

Control Output 2 Through Control Output 0 (CH2 AGC 
State[2:0]) 

Same as 0x035 = 0x12 Control Output 2 through Control 
Output 0 but apply to Rx2. 

0x035 = 0x14 (DIGITAL OVERFLOW) 

Control Output 7 (CH2 Tx Int3 Overflow) 

Same as 0x035 = 0x0A Control Output 7, but applies to Tx2. 

Control Output 6 (CH2 Tx HB3 Overflow) 

Same as 0x035 = 0x0A Control Output 6, but applies to Tx2. 

Control Output 5 (CH2 Tx HB2 Overflow) 

Same as 0x035 = 0x0A Control Output 5, but applies to Tx2. 

Control Output 4 (CH2 Tx QEC Overflow) 

Same as 0x035 = 0x0A Control Output 4, but applies to Tx2. 

Control Output 3 (CH2 Tx HB1 Overflow) 

Same as 0x035 = 0x0A Control Output 3, but applies to Tx2. 

Control Output 2 (CH2 Tx FIR Overflow) 

Same as 0x035 = 0x0A Control Output 2, but applies to Tx2. 

Control Output 1 (CH2 Rx FIR Overflow) 

Same as 0x035 = 0x0A Control Output 1, but applies to Tx2. 

Control Output 0 

Always zero

.

 

0x035 = 0x15 (DC OFFSET TRACKING) 

Control Output 7 (CH1 SOI Present) 

This signal is high when the digital signal power exceeds the RF 
DC offset SOI threshold. In MGC mode, this is always true. For 
AGC modes, this signal will go low when the gain updates. The 
pulse low occurs each time the gain update counter expires (for 
the slow AGC) or when Control Input 2 transitions high (for 
hybrid mode). Time duration of the low pulse is dependent on 
the 

AD9361

 internal clock rates. For the standard LTE 10 MHz 

profile, the duration is approximately 400 ns. In the fast AGC 
mode, the signal will go low while the AGC moves through its 
states. When the gain locks, the signal will transition high if the 
digital signal level exceeds the SOI threshold. 

Control Output 6 (CH1 Update DCRF) 

This signal pulses high when the RF DC offset word updates. 
The duration of the pulse is dependent on the 

AD9361

 internal 

clock rates. For the standard LTE 10 MHz profile, the pulse is 
approximately 30 ns. 

Control Output 5 (CH1 Measure DCRF) 

This signal is high when the RF DC offset is actively being 
calculated and correction words generated. New correction 
words are only applied at times set by DC offset update. In any 
gain control mode, if the gain changes, this signal will be low, 
indicating that the RF DC offset algorithm is waiting for the 
gain to finish changing before calculating new correction 
words. 

Control Output 4 (CH1 DC Track Count Reached) 

This signal pulses high whenever the RF DC tracking count has 
been reached. This event signals that the correction word may 
update with a new value. The value will not be applied until an 
event occurs as specified in DC offset update. The 

AD9361

 

internal clock rates determine the duration of the pulse. For the 
standard LTE 10 MHz profile, the pulse is approximately 30 ns. 

Control Output 3 Through Control Output 0 

Always zero. 

0x035 = 0x16 (GAIN CONTROL) 

Control Output 7 (CH1 Gain Lock) 

See 0x035 = 0x08 Control Output 6. 

Control Output 6 Through Control Output 0 (CH1 Rx 

Gain[6:0]) 

These signals represent the gain index of Rx1 but only apply to 
AGC modes. For the full gain table mode, this is the index of 
the full gain table. For the split gain table mode, this index is for 
the LMT table. The BBP must read the index of the LPF table 
using SPI reads.

 

 

 

Rev. A

Summary of Contents for AD9361

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands