manualshive.com logo in svg

Analog Devices AD9361, Reference Manual

Share
Download
Analog Devices AD9361 Reference Manual Download Page 26

UG-570 

AD9361 Reference Manual 

 | Page 26 of 128 

MODES OF OPERATION 

The ENSM can either be controlled by SPI writes or the 
ENABLE/TXNRX pins. SPI control is considered asynchronous 
to the DATA_CLK because the SPI_CLK can be derived from a 
different clock reference and still function properly. The SPI 
control ENSM method is recommended when real time control 
of the synthesizers is not necessary. SPI control can be used for 
real time control as long as the BBP has the ability to perform 
timed SPI writes accurately. The ENABLE/TXNRX pin control 
method is recommended if the BBP has extra control outputs 
that can be controlled in real time, allowing a simple two-wire 
interface to control the state of the 

AD9361

 device. The 

ENABLE pin can be driven by either a pulse (edge detected 
internal to the 

AD9361

) or a level to advance the current state 

of the ENSM to the next state. If a pulse is used on the ENABLE 
pin, it must have a minimum pulse width of one FB_CLK cycle. 
In level mode, the ENABLE and TXNRX pins are also edge 
detected in the 

AD9361

, and must meet the same minimum 

pulse width requirements of one FB_CLK cycle.  

SPI Control 

SPI control is disabled by default and can be enabled in the 
ENSM Config 1 register. Once in the ALERT state, the 

AD9361

 

enables its RF synthesizers for the transmitters and receivers. If 
for some reason the synthesizers did not calibrate correctly, the 
ENSM will not be able to transition to the Rx or Tx states. This 
feature protects the 

AD9361

 from transmitting or receiving data 

when the synthesizers are not calibrated properly, protecting the 
wireless spectrum.  
Once in the ALERT state, with the RFPLLs properly calibrated, 
the ENSM is ready to move into the Rx, Tx, or FDD state. To 
move from ALERT to Rx, set the Force Rx On bit. To move 
back to ALERT or WAIT, clear the bit. To move from ALERT to 
Tx or FDD, set the Force Tx On bit. To move back to ALERT or 
WAIT clear the bit. In FDD mode, the Force Rx On bit is 
ignored. While in TDD, the ENSM must transition to the 
ALERT state between Rx and Tx states. The ENSM cannot 
move from Rx directly to Tx, or Tx directly to Rx.  
After sending the Force Alert State bit from the WAIT state, 
allow the ENSM time to pass through ENSM State 4 before 
sending another command. The time for State 4 to complete 
depends on the time setting written into the Rx and Tx Load 
Synth Delay registers. This delay is 2 µs.  
After sending the SPI write to exit the Rx or Tx states, allow six 
ADC_CLK/64 clock cycles of flush time before sending another 
ENSM SPI command. If a SPI command is received during an 
intermediate ENSM state, the command will be ignored.  

Rev. A

Summary of Contents for AD9361

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands